Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Return appliance to authorized service center for examination, repair or adjustment. 9) Do not touch the moving parts of the appliance when operating. 3 10) Do not use attachments or accessories not recommended or sold by the manufacturer. They may cause fire, electric shock or injury. 11) Unplug the appliance from the outlet when not in use, assembling and disassembling, and before cleaning. Make sure the appliance stops completely before disassembling. 12) Do not let cord hang over edge of table or counter, or touch hot surfaces. 13) Do not place the appliance on or near a burner or a hot oven. 14) When blending hot liquids, remove centerpiece of two-piece cover. 15) Blades are sharp. Handle carefully. 16) Be certain cover is securely locked in place before operating appliance. CAUTION: This product is equipped with a polarized plug (one blade is wider than the other blade) as a safety feature to reduce the risk of electrical shock. This plug will fit into a polarized outlet only one way. This is a safety feature. If you are unable to insert the plug into the electrical outlet, try reversing the plug. If the plug still does not fit, contact a qualified electrician. Never use the plug with an extension cord unless the plug can be fully inserted into the extension cord. Do not alter the plug of the appliance or any extension cord used with this appliance. Do not attempt to defeat the safety purpose of the polarized plug. SAVE THESE INSTRUCTIONS 4 Parts and Feature 1 - Pouring hole cover 2 - Lid 3 - Blender Jar 4 - Blade assembly 5 - Lid safety lock 6 - Motor base 7 - Off button 8 - 10 speeds buttons 9 -High / Low button High position – ‘H’ for speed 6 to speed 10 Low position – ‘L’ for speed 1 to speed 5 10 - Pulse button 11 - Non-slip rubber feet 5 Assembling Blender To use the blender, start by assembling the blender jar (3), and then place the blender jar (3) on the motor base (6) as described below. Assembling: 1) Put the motor base (6) on a steady and even surface 2) Place the rubber seal ring on the blade assembly (4). 3) Position the blade assembly (4) on the inside of the blender jar(3). 4) Turn it counter-clockwise to lock it tightly into position. Important: The blade is sharp. Handle carefully. 5) Position the blender jar (3) on the motor base (6) and turn it clockwise to lock it into position. 6) Position the lid (2) on the blender jar(3) Note: The tail of the lid should be placed on the slot at the top of the handle as per 2-way safety system 2-Way Safety System 1) Safety lock on lid : When lid is removed, the blender will stop operation. When positioning the lid on the blender jar, note that the tab on the lid should be put into the slot on the top of the handle to lock it into position. 2) Safety lock between the blender jar assembly and the motor base: When the blender jar is detached from the motor base, the unit will not operate. Align the arrow on the blender jar with the arrow on the motor base of the unit. This is achieved by turning the blender jar clockwise, until the blender jar snaps into place when the arrows are aligned. 3) With the 2-way safety system, it is only possible to operate when both the blender jar and the lid are located in the proper position. 6 Operating Instructions 1) Always place the blender on a flat, clean and non-slippery surface before operating it. 2) Open the lid and add all necessary ingredients to the blender jar. Replace the lid and the pouring hole cover. 3) For using low speeds (1-5) the ‘H’ / ‘L’ button must be recessed, then choose low speeds 1-5. To change to high speeds (6-10) turn unit off, make sure the ‘H’ / ‘L’ button is up, then choose speeds 6-10. Caution: Always first turn unit off, before switching from Hi speeds to Low speeds or low speeds to high speeds. 4) To use the pulse button, you must hold to press for operating. The blender will stop when you release the pulse button. 5) When the blending is finished, turn the jar anti-clockwise and lift it off the base. Then remove the lid. Pour the ingredients out through the spout. 6) Do not operate the blender longer than 2minutes. After each the 2 minutes session the blender must be allowed to cool down for at least 10 minutes. 7 Cleaning and Maintenance 1) Always unplug the blender from the electrical outlet before cleaning. 2) Pour warm water and some drops of washing detergent into the jar. 3) Mix the liquid by pressing the pulse button for a short while. Caution: handle the blade assembly carefully. It is sharp and may cause injury. Do not attempt to remove blades from cutting assembly. 8 Magic Chef Limited Warranty This Magic Chef product is warranted, to the original purchaser or gift recipient, to be free from any manufacturing defects under normal use and conditions for a period of one (1) year from the date of purchase as shown on retailer’s receipt. The obligation of Magic Chef under this warranty shall be limited to repair or replacement (at our option) during the warranty period, of...