Stimmen - 5, Durchschnittliche Bewertung: 4.4 ( )

Hersteller: Bravetti Dateigröße: 136.33 kb Dateiname: Unterrichtssprache:

Variable Speed Control There is a variable speed control located at the top of the power pack. To vary the speed of your blender rotate the round knob at the top of the power pack. From the low setting turn the variable speed control clockwise to increase speed and counterclockwise to reduce speed. Fig. 1 Operating Instructions Assembling the Stick Blender: Make sure that the unit is unplugged from power source before attaching or removing any of the stick blender attachments. WARNING: This appliance is designed for intermittent use. Maximum running time with the stick blender is 1 minute. After this time, allow the unit to cool. 1. Line up arrow of stick blender attachment with arrow on power pack. Once fully inserted, rotate stick blender attachment clockwise 90. until arrow on power pack aligns with square on stick blender. (Fig. 2) 4. Place the metal stick blender first into the food to be chopped or pureed before pressing the On/Off Switch to avoid spattering. 5. Use the variable speed control knob to select the desired speed. 6. Always release the On/Off switch before removing the stick blender from the food especially when using the stick blender in hot liquids. Always hold the unit with your hand while processing. Never leave the unit unattended or hook it on the wall bracket when it is plugged in. 7. To remove the stick blender attachment from the power pack, first unplug the unit from the power source and turn only the stick blender attachment 90° counter- clockwise and pull it off. Using the Stick Blender Pureeing soups, sauces, fruits and vegetables: • Fruits and vegetables should be peeled, cored and seeded. • Meats, poultry, and fish should have skin and bones removed. • Food should be cut up into pieces no larger than 3/4-inch. • Cook the food in liquid until very soft and tender. • Puree cooked food ONLY after allowing to cool down. • Food can also be pureed directly in the pot after being allowed to cool. • Place the Stick Blender in the center of the food in an upright position with the processor end resting directly on the bottom of the bowl or pot. • The processor end must always be immersed in the food. DO NOT lift up and out of food while operating since the hot food will splatter and could cause burns. • While holding the power pack and the stick blender in your hand, press and hold down on the switch with your index finger. • Release once the food has the desired consistency. 4 Fig. 2 2. Plug the cord into an electrical outlet. CAUTION: To avoid splattering, place the stick blender first in the food to be beaten or chopped, then press the button. Always release the button before removing the stick blender from the food, especially when using the stick blender in hot liquids. Always hold the stick blender with your hand while processing. Never leave unit unattended. CAUTION: Do not use the Stick Blender on the stove. If you want to use it in a saucepan while cooking, you must first remove saucepan from the stove. 3. Use the beaker with the stick blender or you can use another container. The beaker is intended only for processing small quantities of food with the stick blender. Operating Instructions • Do not operate continuously for more than 1 minute. • If pieces of unprocessed food remain, or if there are any lumps, continue pureeing the food, however, mash the food pieces or lumps by slightly raising and then lowering the stick blender over those pieces. Multi- Mixer Assembly CAUTION: Ensure that the appliance is unplugged from the electrical power source before changing attachments. Do not immerse the mixer gear box in water. 1. To attach the mixer gear box to the power pack, line up arrow on the power pack and mixer gear box. 2. Push power pack onto mixer gear box until seated. 3. While grasping mixer gear box rotate it 90. clockwise until the arrow on the power pack aligns with the “Square” on the mixer gear box. 4. To disassemble mixer gear box and power pack rotate mixer gear box 90. counterclockwise. Attaching the Attachments to the Gear Box CAUTION: Ensure that the appliance is unplugged from the electrical power source before changing attachments. Do not immerse the gear box in water. Select the desired attachment, either the dough hooks, wire beaters or whisk and assemble to gear box as noted below: Note: When inserting dough hooks or beater attachments, make sure to insert the piece with the ring on the shaft into the larger opening of the gear box. 5 1. After attaching the desired accessory into the gear box, plug the mixer into power source. 2. Hold the power pack with one hand and press and hold the On/Off switch with your index finger. 3. Ensure that there are no obstructions and that the accessories are moving freely in the mixing container. 4. When finished using the unit, unplug the unit before removing the accessories. Dough Hooks (x2) : For use with light dough ONLY. • Insert stem end of dough hooks (one at a time) into opening in base of gear box. • Rotate sligh...

Herunterladen

Geben Sie zwei Ziffern: