Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
5 inches of space between the back and sides of the appliance, allows the proper air circulation to cool the compressor, e the appliance away from direct sunlight and sources of heat i, heater, radiator, etc. ) . Direct sunlight may affect the acrylic g and heat sources may increase electrical consumption. Extreme 4 cold ambient temperatures may also cause the appliance not to perform properly. • Avoid locating the appliance in moist areas. Too much moisture in the air will cause frost to form quickly on the evaporator, requiring more frequent defrosting of the wine cooler. • Plug the appliance into an exclusive properly installed - grounded wall outlet. Do not under any circumstances cut or remove the third (ground) prong from the power cord. Any questions concerning power and or grounding should be directed toward a certified electrician or an authorized Avanti Products Service center. y Warning/^ Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by an authorized Avanti Products service center. Installing the Door Handle • Place the handle over the two holes in the upper left side of the door. • Attach using the two Phillips screws provided. ^ Reversing the Door Swing of Your Wine Cooler This wine cooler has the capability of either opening the door from the left or right side. The unit is delivered to you with the door opening from the left side. Should you desire to reverse the opening direction, please follow these instructions. NOTE: All parts removed must be saved to do the reinstallation of the door. Removal of the Wine Cooler Door 1 • Remove the upper hinge cap(1 ). 2 • Using a sharp object, pry out the two plug buttons(10). • Remove the two Phillips screws(2) that connect the upper hinge (3) on the right side of the cabinet top. • Carefully lift the door, placing it on a padded surface to avoid scratching. • Remove the plug (9) and transfer it to the uncovered hole at the right side. Be sure to press the button firmly into the hole • Remove the two bolts (7) that hold the lower 5 hinge (4) on the right side. • Remove the adjustable leveling leg(8) and transfer it to the right side. • Reattach the lower hinge(4) on the left side by attaching the adjustable leveling leg (8) and two bolts(7). Reversal and Installation of Wine Cooler Door tho • Set enters • While hinge u the upp • Before cabine • Replade • Replao corner • Chang Changing wine cooler door in its new position, making sure the hinge Pin he bushing at the bottom of the cabinet. holding the door in the closed position, loosely secure the upper sing the two Phillips screws. Be sure the pin enters the bushing at er and lower frame section (holes). tightening the screws, be sure the top of the door is level with the top. the upper hinge cover(1). e the two plug buttons(10) in the holes now on the top right of the unit. ? the position of the handle the Position of the Handle doo • Remo\ • Place the • Reatta NOTE: Before ti the top o e the two Phillips screws attaching the handle, he handle over the two holes located on the upper right corner of r. ;h using the two Phillips screws. ightening these screws, make sure the top of the door is level with the cabinet. OPERATING YOUR WINE COOLER ure Control • The first time you turn the unit on , set the temperature control to "MAX" positior], • The st and “NORI\H> fice wir e • To turr NOTE: • Turning but dogs • If the e(tings of the temperature control are“OFF”, “MIN”, "NORMAL” MAX” . After 20 minutes, adjust the temperature control setting to AL". The setting of“NORMAL” should be correct for home or of-e cooler use. the wine cooler off, turn the temperature control to“OFF”. the temperature control to“OFF”position stops the cooling cycle, s not shut off the power to the wine cooler. is unplugged, power lost, or turned off, you must wait 3 to 5 unit 6 minutes before restarting the unit. If you attempt to restart before this time delay, the wine cooler will not start. •The range between“MIN”and“MAX”is from 48°F to 61 °F, which is ideal for the storage of wines at the " NORMAL" setting. CARE AND MAINTENANCE ^ Cleaning Your Wine Cooler • Turn the temperature control to“OFF", unplug the wine cooler, and remove the bottles. • Wash the inside with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water. • Wash the shelves and trays with a mild detergent solution. • The outside of the wine cooler should be cleaned with mild detergent and warm water. • It may also be necessary to periodically wipe the bottom part of the storage area, as the wine cooler is designed to retain humidity, and condensation may collect there. • Dry the water collection tray located above the compressor in the back of the unit. Once dry, place it back to its original position. ^ Maintenance of Your Wine Cooler • Power Failure Mos...