Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Actiontec electronic Dateigröße: 1.04 mb Dateiname: Unterrichtssprache:

Two high-pitched tones will sound, followed by two more tones, and then the red and blue lights will flash. 2. On the computer, open the Bluetooth Configuration screen and double- click Find Bluetooth Devices. Note:The Bluetooth Configuration setup may differ based on . the brand of the Bluetooth adapter you are using. 3. Place the Headset firmly in either ear. 4. On the computer, Right-click on the CSR-bc2 icon. From the menu that appears, select Pair Device. 8 Chapter 2 Using the Headset 5. A new window appears, requesting a passkey to connect to the Headset. Enter 1234, then press Enter. 6. The Headset icon turns green. The Headset is successfully connected to the computer. Connecting to Other Devices To connect the Headset to another type of device (a PDA, for example), the device must support Audio Gateway Profiles. Refer to the user manual of the other device to set up the Headset. 9 Actiontec Wireless Bluetooth Headset User Manual 10 Troubleshooting 3 This section details problems that may occur when using the Headset, and solutions for them. The Red Light is flashing. What does this mean? When only the Red light is flashing, the Headset’s rechargeable battery is running low. Plug the Headset into a wall outlet via the power adapter and recharge the battery. Full recharge takes approximately two hours. I charged the Headset’s battery for 20 minutes, but it still doesn’t work. What can I do? The Headset’s rechargeable battery must be charged for at least 40 minutes before it can be used. It is recommended, however, that the battery be charged for the full two hours. I plugged the Headset into an electrical socket, but it doesn’t appear to be recharging. What’s going on? If the Headset hasn’t been used for a long time, or the battery is nearly empty, it may take a few minutes for the Red Light to flash and indicate that it is recharging. I am getting no sound between the Headset and the device it’s connnected to. What should I do? Check the following: •Make sure the Headset and the device have been paired. •Make sure the Headset is turned on. •Make sure the Headset and the device are withn working range of each other. •Ifconnecting to a cellular phone, make sure it has good signal strength. •Some cellular phones support only one Bluetooth headset at a time. Disconnection can occur if more than one Headset is being used. 11 Actiontec Wireless Bluetooth Headset User Manual 12 Notices Regulatory Compliance Notices Class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by implementing one or more of the following measures: • Reorient or relocate the receiving antenna; • Increase the separation between the equipment and receiver; • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected; • Consult the dealer or an experienced radio or television technician for help. Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Actiontec Electronics, Inc., may void the user’s authority to operate the equipment. Declaration of conformity for products marked with the FCC logo – United States only. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.This device may not cause harmful interference; 13 Actiontec Wireless Bluetooth Headset User Manual 2. This device must accept any interference received, including interference that may cause unwanted operation. . Note:To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. For questions regarding your product or the FCC declaration, contact: Actiontec Electronics, Inc. 760 North Mary Ave. Sunnyvale, CA 94086 United States Tel: (408) 752-7700 Fax: (408) 541-9005 14 Limited Warranty Hardware: Actiontec Electronics, Inc., warrants to the end user (“Customer”) that this hardware product will be free from defects in workmanship and materials, under normal use and service, for twelve (12) months from the date of purchase from Actiontec Electronics or its authorized reseller. Actio...

Herunterladen

Geben Sie zwei Ziffern: