Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Poulan, modell 633GC

Hersteller: Poulan
Dateigröße: 1.04 mb
Dateiname: ICS_633GC_OpManual.pdf

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

P/N 70944 Jan 07 633GC OPERATOR’S MANUAL TABLE OF CONTENTS SYMBOLS & LABELS 4 SAFETY 5 TECHNICAL SPECIFICATIONS 8 SET-UP 9 OPERATION 12 MAINTENANCE 17 TROUBLESHOOTING 25 REFERENCE 26 P/N 70944 Jan 07 © 2007 ICS, Blount Inc. SYMBOLS & LABELS 633GC OPERATOR’S MANUAL THE FOLLOWING SYMBOLS & DEFINITIONS ARE FOUND THROUGHOUT THIS MANUAL AND ARE DESIGNED TO MAKE YOU AWARE OF POTENTIAL HAZARDS OR UNSAFE PRACTICES. WARNING product or property damage. A potentially hazardous situation exists which, if not avoided, could result in death or serious injury. CAUTION A potentially hazardous situation exists which, if not avoided, may result in minor or moderate injury or property damage. IMPORTANTA potential situation exists which, if not avoided, may result in THE FOLLOWING SYMBOLS & LABELS MAY BE FOUND IN THIS MANUAL OR ON THE SAW Read the operator’s manual carefully and understand the contents before you use this equipment. Always use: • Protective helmet • Ear protection • Protective glasses or full face protection Wear hand protection © 2007 ICS, Blount Inc. P/N 70944 Jan 07 633GC OPERATOR’S MANUAL SAFETY THE FOLLOWING SYMBOL APPLIES TO ALL THE ITEMS LISTED ON THIS PAGE WARNING A potentially hazardous situation exists which, if not avoided, could result in death or serious injury. Chain breakage can result in high-speed ejection of parts, which can result in death or serious personal injury to operators or bystanders. The items listed below are critical to minimizing the risk of chain breakage and injury. • DO NOT operate a diamond chainsaw with a damaged, modified, broken, or missing side cover, bottom guard, or guard flap. The side cover, bottom guard, and guard flap provides protection against contact with moving parts, ejected debris, broken diamond chain, thrown water and concrete slurry. • DO NOT operate a saw with loose, missing, damaged or improperly repaired parts. • DO NOT install or run the chain backwards. The bumper must lead the segment into the cut. • DO NOT insert a diamond chainsaw into a slot narrower than the chain segments. Rapid pushback might occur. Reference: Most diamond segments are .225 inches (5.72 mm) wide. • DO NOT use damaged, modified or improperly repaired chain. • DO NOT run a diamond chainsaw upside-down. Concrete debris can fly back into the operator’s face. • DO NOT cut ductile iron pipe with a diamond chainsaw. Segment loss or chain breakage may occur. P/N 70944 Jan 07 © 2007 ICS, Blount Inc. SAFETY 633GC OPERATOR’S MANUAL THE FOLLOWING SYMBOL APPLIES TO ALL ITEMS LISTED ON THIS PAGE CAUTION A potentially hazardous situation exists which, if not avoided, may result in minor or moderate injury or property damage. • Always turn a diamond chainsaw OFF when performing maintenance on the saw including chain tensioning. • Never use equipment that is not functioning properly. Have the saw repaired by qualified service personnel. • Turn engine OFF before refueling. Keep away from open flame. Always provide adequate ventilation when handling fuel. Move diamond chainsaw at least 10 feet (3 m) away from refueling area before starting. • SealPro® diamond chains require a minimum water pressure of 20 psi (1.4 bar). Insufficient water supply may result in excessive wear to the chain, which can lead to loss of strength and chain breakage. • Never start a diamond chainsaw unless the bar, chain and side cover are properly installed. GENERAL SAFETY PRECAUTIONS • Always wear protective clothing, including hard hat, eye protection, hearing protection, and gloves. • Avoid loose fitting clothing. • Perform safety checks before starting each day. • Always operate tool with solid footing and with both hands on saw. • Remove or control slurry to prevent slippery conditions while cutting. • Be sure there are no obstructions (plumbing, electrical conduit, air ducts) and no unnecessary people present. • Set up a well-marked safety zone with a roped boundary and clear signs. • Provide adequate ventilation when working in an enclosed area. Breathing exhaust gases is dangerous. • To avoid electrocution, check for live electrical wiring near cutting area. © 2007 ICS, Blount Inc. P/N 70944 Jan 07 633GC OPERATOR’S MANUAL SAFETY THE FOLLOWING SYMBOL APPLIES TO ALL ITEMS LISTED ON THIS PAGE A potential situation exists which, if not avoided, may result in IMPORTANT product or property damage. Note: The diamond chainsaw is equipped with a two-stroke engine and must always be run using a mixture of gasoline and ICS® two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. • This engine is designed to be operated on premium unleaded gasoline. • Use high quality, unleaded gasoline with a minimum octane rating of 90. If lower octane gasoline is used, engine temperature will increase which will result in a piston seizure and damage to the...