Stimmen - 1, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
WARNING APPLICABLE SERIAL NUMBERS : 200101 and up G3000 The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. WARNING Before using our products, please read this manual carefully to understand the proper use of your unit. WARNING APPLICABLE SERIAL NUMBERS : 200101 and up G3000 SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ¦ WARNINGS IN THE MANUAL WARNING This mark indicates instructions which must be followed in order to prevent accidents which could lead to serious bodily injury or death. IMPORTANT This mark indicates instructions which must be followed, or it leads to mechanical failure, breakdown, or damage. NOTE This mark indicates hints or directions useful in the use of the product. CONTENTS 1. Parts location …………………………………4 2. Specifications …………………………………4 3. Symbols on the machine ……………………5 4. For safe operation ……………………………6 5. Installing guide bar and saw chain …………8 6. Fuel and chain oil ……………………………9 7. Operation ……………………………………10 8. Sawing ………………………………………13 9. Maintenance …………………………………16 10. Storage ………………………………………19 1. Guide Bar 2. Saw Chain 3. Front Guard 4. Front Handle 5. Rear Handle 6. Chain Cover 7. Fuel Tank Cap 8. Oil Tank Cap 9. Air Cleaner ··············· .4 . 3. Symbols on the machine For safe operation and maintenance, symbols are on the machine. According to these indications, please be careful not to take a mistake. (a). The port to refuel the “MIX GASOLINE” Position: fuel tank cap (b). The port to refuel the “CHAIN OIL” Position: oil cap (c). The indication regarding the switch. Flipping the engine switch to the “O” (STOP) direction, the engine stops. Position: upper part of the unit (d). The indication regarding the choke. Pulling out the choke knob, the choke closes. Position: front of the chain cover (e). The position of H-needle The position of L-needle The position of idle adjusting screw Position: Front of the chain cover .5 . 4. For safe operation 1. Never operate a chain saw when you are fatigued, ill, or upset, or under the influence of medication that may make you drowsy, or if you are under the influence of alcohol or drugs. 2. Use safety footwear, snug fitting clothing and eye, hearing and head protection devices. 3. Always use caution when handling fuel. Wipe up all spills and then move the chain saw at least 3m from the fueling point before starting the engine. 3a) Eliminate all sources of sparks or flame (ie. smoking, open flames, or work that can cause sparks) in the areas where fuel is mixed, poured, or stored. 3b) Do not smoke while handling fuel or while operating the chain saw. 4. Do not allow other persons to be near the chain saw when starting the engine or cutting a wood. Keep bystanders and animals out of the work area. Children, pets, and bystanders should be a minimum of 10m away when you start or operate the chain saw. 5. Never start cutting until you have a clear work area, secure footing, and planned retreat path from the falling tree. 6. Always hold the chain saw firmly with both hands when the engine is running. Use a firm grip with thumb and fingers encircling the chain saw handles. 7. Keep all parts of your body away from the saw chain when the engine is running. 8. Before you start the engine, make sure the saw chain is not contacting anything. 9. Always carry the chain saw with the engine stopped, the guide bar and saw chain to the rear, and the muffler away from your body. 10. Always inspect the chain saw before each use for worn, Ioose, or changed parts. Never operate a chain saw that is damaged, improperly adjusted, or is not completely and securely assembled. Be sure that the saw chain stops moving when the throttle control trigger is released. 11. All chain saw service, other than the items listed in the Operator’s Manual, should be performed by competent chain saw service personnel. (e.g., if improper tools are used to remove the flywheel, or if an improper tool is used to hold the flywheel in order to remove the clutch, structural damage to the flywheel could occur which could subsequently cause the flywheel to disintegrate). 12. Always shut off the engine before setting it down. 13. Use extreme caution when cutting small size brush and saplings because slender material may catch the saw chain and be whipped toward you or pull you off balance. 14. When cutting a limb that is under tension, be alert for spring back so that you will not be struck when the tension in the wood fibers is released. 15. Keep the handles dry, clean and free of oil or fuel mixture. .6 . 4. For safe operation 16. Operate the chain saw only in well ventilated areas. Never start or run the engine inside a closed room or buildin...