Stimmen - 5, Durchschnittliche Bewertung: 3.8
(
)
)
|
Fotos und technische Daten Stihl MS 261 |
Anleitung Zusammenfassung
If this tool is subjected to unusually high loads for which it was not designed (e.g. heavy impact or a fall), always check that it is in good condition before continuing work. Check in particular that 001BA115 KN the fuel system is tight (no leaks) and that the controls and safety devices are working properly. Do not continue operating this machine if it is damaged. In case of doubt, have it checked by your STIHL servicing dealer. THE USE OF THE POWER TOOL Transporting the Power Tool Warning! To reduce the risk of injury from saw chain contact, never carry or transport your power tool with the saw chain moving. Always engage the chain brake when taking more than a few steps. Warning! Always switch off the engine, and fit the chain guard (scabbard) over the chain and guide bar before transporting the power tool over longer distances. When transporting it in a vehicle, properly secure it to prevent turnover, fuel spillage and damage to the unit. It may be carried only in a horizontal position. Grip the front handle in a manner that the machine is balanced English horizontally. Keep the hot muffler away from your body and the cutting attachment behind you. Fuel Your STIHL power tool uses an oil- gasoline mixture for fuel (see the chapter on "Fuel" of your instruction manual). Warning! Gasoline is an extremely flammable fuel. If spilled and ignited by a spark or other ignition source, it can cause fire and serious burn injury or Warning! g Instructions F property damage. Use extreme caution whe handling gasoline or fuel mix. Do no or bring any fire or flame near the fuel or the power tool. Note that combustible fuel vapor may escape fr fuel system. Fuel your power tool in well-ventilated areas, outdoors. Always shut off the engine and allow it to cool before refueling. Gasoline vapor pressure may build up inside the fuel tank depending on the fuel used, the weather conditions and the tank venting system. In order to reduce the risk of burns and other personal injury from escaping gas vapor and fumes, remove the fuel filler cap on your power tool carefully so as to allow any pressure build-up in the tank to release slowly. Never remove the fuel filler cap while the engine is running. MS 261, MS 261 C English Select bare ground for fueling and move at least 10 feet (3 m) from the fueling spot before starting the engine. Wipe off any spilled fuel before starting your machine. D nt models may be equipped with di ent fuel caps. T ss cap with grip Misaligned, damaged or broken cap NIf the cap does not drop fully into the opening when the positioning marks line up and/or if the cap does not NTo return the cap to the open Warning! Check for fuel leakage while refueling and during operation. If fuel leakage is found, do not start or run the engine until the leak is fixed and a illed fuel has been wiped away. T ke care not to get fuel on your cloth- i this happens, change your clothing immediately. Warning! you must repeat the above steps. you must repeat the above steps. marks on the grip of the cap and on the fuel tank opening lining up. Using the grip, press the cap down firmly while turning it clockwise as far as it will go (approx. 1/4 turn). Fold the grip flush with the top of the cap. Grip the cap and check for tightness. If the grip does not lie completely flush with the cap and the detent on the grip does not fit in the corresponding recess in the filler 001BA227 KN Left: Base of cap in closed position (with open space) Right: Base of cap correctly positioned for installation opening, or if the cap is loose in the filler opening, the cap is not properly seated and tightened and 001BA226 KN position for installation, turn the cap In order to reduce the risk of fuel spill- tighten properly when twisted, the (with the grip up) until it drops fully into the tank opening. Next, twist the age and fire from an improperly base of the cap may be prematurely tightened fuel cap, correctly position rotated (in relation to the top) to the cap counterclockwise as far as it will go (approx. 1/4 turn) – this will twist and tighten the fuel cap in the fuel tank closed position. Such misalignment opening. can result from handling, cleaning the base of the cap into the correct or an improper attempt at position. Then, twist the cap tightening. 001BA220 KN clockwise, closing it normally. N If your cap still does not tighten properly, it may be damaged or broken; immediately stop use of the unit and take it to your authorized STIHL dealer for repair. To do this with this STIHL cap, raise the grip on the top of the cap until it is upright at a 90° angle. Insert the cap in the fuel tank opening with the raised positioning MS 261, MS 261 C English Screw Cap Warning! Unit vibrations can cause an improperly tightened fuel filler cap to loosen or come off and spill quantities of fuel. In order to reduce the risk T ke off the chain guard (scabbard) and i spect the saw for proper condition and operation. (See the maintenance chart near the...