Login:
Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Desa, modell EL-7 099039J

Hersteller: Desa
Dateigröße: 1.03 mb
Dateiname:

Unterrichtssprache:en

Das Dokument wird geladen, bitte warten
Das Dokument wird geladen, bitte warten

Anleitung Zusammenfassung


This is done while in normal cutting position and cutting with top of guide bar. For more information, visit 4 OWNER’S MANUAL Power Cord Rear Hand Guard Rear Handle Front Hand Guard Guide Bar Sprocket Cover Saw Chain Guide Bar Nose Scabbard PRODUCT IDENTIFICATION UNPACKING 1. Remove all items from carton. 2. Check all items for any shipping damage. If you find any damage or if any parts are missing, promptly inform dealer where you bought chain saw. Oil Level Sight Hole Oil Cap With Squeeze Bulb TriggerSwitch LockoutMotor Housing Figure 2 - Electric Chain Saw (located on saw body, hidden by front handle) Front Handle Spike 5 For more information, visit ® ® ELECTRIC CHAIN SAW ASSEMBLY Note:Some models are pre assembled. Assembly is not needed on these models. See Saw Chain Tension Adjustment, page 7. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. IMPORTANT: Do not clamp chain saw in vise during assembly. The plastic hardware bag should include: • two guide bar bolts • two guide bar nuts • one Phillips-head tapping screw • automatic chain sharpener (Fast Sharp models only) 1. Lay chain out flat. 2. Install front hand guard onto saw body. Do this by pressing two mounting standouts on hand guard into hex-shaped holes in saw body (see Figure 3). Insert tapping screw through hand guard and into saw handle. Tighten screw firmly. 4. Turn adjusting screw counterclockwise (see Figure 4). Continue to turn adjusting screw until adjusting block is to rear of adjusting plate. 5. Install guide bar onto saw body. Place rear of guide bar between adjusting plate and sprocket support. IMPORTANT:Make sure to insert adjusting block into oval adjusting hole on guide bar. 6. Line up holes on sprocket support with center slot on guide bar and holes in saw body. 7. Insert guide bar bolts through front hand guard, saw body, center slot of guide bar, and sprocket support. Attach guide bar nuts to guide bar bolts. IMPORTANT:Tighten guide bar nuts finger tight only. Make sure adjusting block is in oval adjusting hole on guide bar. 8. Place chain around drive sprocket, then along top groove of guide bar and around guide bar nose. Note: Make sure cutting edges of chain are facing the right direction. Position chain so cutting edges on top of guide bar face guide bar nose (see Figure 3). Tapping Front Hand CAUTION: Do not place chain on saw backwards. If chain is backwards, saw will vibrate badly and will not cut. 9. Adjust saw chain tension. Follow steps under Saw Chain Tension Adjustment, page 7. Mounting Stand-Outs Guide Bar Bolts Guide Bar Nuts Adjusting Hole Guide Bar Screw Saw Chain Cutting Edge Cutting EdgeTowards Guide Bar Nose Guard Drive Sprocket Figure 3 - Assembling Guide Bar, Chain, and Hand Guard Adjusting Plate Adjusting Screw Sprocket Support Adjusting Block Figure 4 - Part Locations For Assembling Guide Bar For more information, visit 6 107990 7 OWNER’S MANUAL For more information, visit Note: For pre-assembled models, the saw chain tension is properly set at factory. A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Follow steps below to readjust saw chain tension. 1. Before adjusting chain, make sure guide bar nuts are only finger tight (see Figure 3, page 6). Also make sure adjusting block is in oval adjusting hole on guide bar (see Figures 3 and 4, page 6). 2. Turn adjusting screw clockwise until all slack is out of chain (see Figure 5). Note: There should be no gap between side links of chain and bottom of guide bar (see Figure 6). 3. Wearing protective gloves, move chain around guide bar. Chain should move freely. If chain does not move freely, loosen chain by turning adjusting screw counterclockwise. SAW CHAIN TENSION ADJUSTMENT WARNING: Unplug chain saw from power source before adjusting saw chain tension. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. WARNING: Maintain proper chain tension always. A loose chain will increase the risk of kickback. A loose chain may jump out of guide bar groove. This may injure operator and damage chain. A loose chain will cause chain, guide bar, and sprocket to wear rapidly. Figure 5 - Turning Adjusting Screw Guide Bar Correct Tension Guide Bar Gap Incorrect Tension Guide Bar Nuts Figure 6 - Saw Chain Adjustment 1. Remove oil cap. 2. Fill oil tank with SAE #30 motor oil. Note: For temperatures below 30°F, use SAE #10 oil. For temperatures above 75°F, use SAE #40 oil. 3. Replace oil cap at once. Tighten oil cap firmly for good seal. This will avoid oil seepage from tank. 4. Wipe off excess oil. Note: It is normal for oil to seep when saw is not in use. Empty oil tank after each use to prevent seepage. 4. After chain tension is correct, tighten FILLING OIL TANK guide bar nuts firmly. If not, guide bar will move and loosen chain tension. This will increase the risk of kickback. This ca...

Dieses Handbuch ist für folgende Modelle:
Kettensägen - 076728K, 099178H, 100089-06, 100089-08, 107709-01,075762J, 098031J, 099039J, 100089-04, 100089-05, 1 (1.03 mb)
Kettensägen - EL-7 098031J (1.03 mb)
Kettensägen - EL-7 100089-04 (1.03 mb)
Kettensägen - EL-7 100089-05 (1.03 mb)

Bewertungen



Bewerten
Vorname:
Geben Sie zwei Ziffern:
capcha





Kategorien