Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Desa Dateigröße: 606.94 kb Dateiname: Unterrichtssprache:

Switch Linkage This device connects switch to trigger. It moves switch when you squeeze trigger. Switch Lockout Device that reduces accidental starting of saw. Trigger Device that turns saw on and off. Squeezing trigger turns saw on. Releasing trigger turns saw off. Trimming (Pruning) Process of cutting limb(s) from a living tree. Undercut An upward cut from underside of log or limb. This is done while in normal cutting position and cutting with top of guide bar. 4 097017 OWNER’S MANUAL Power Cord Rear Hand Guard Rear Handle Front Hand Guard Guide Bar Spike Saw Chain Guide Bar Nose Scabbard PRODUCT IDENTIFICATION UNPACKING 1. Remove all items from carton. 2. Check all items for any shipping damage. If you find any damage or if any parts are missing, promptly inform dealer where you bought chain saw. Oil Level Sight Hole Oil Cap TriggerSwitch LockoutMotor Housing (located on saw body, hidden by front handle) Front Handle Figure 2 - Electric Chain Saw 097017 5 ® ® ELECTRIC CHAIN SAW ASSEMBLY Note:Some models are pre assembled. Assembly is not needed on these models. See Saw Chain Tension Adjustment, page 7. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. IMPORTANT: Do not clamp chain saw in vise during assembly. The plastic hardware bag should include: • two guide bar bolts • two guide bar nuts • one Phillips-head tapping screw • automatic chain sharpener (Fast Sharp models only) 1. Lay chain out flat. 2. Install front hand guard onto saw body. Do this by pressing two mounting standouts on hand guard into hex-shaped holes in saw body (see Figure 3). Insert tapping screw through hand guard and into saw handle. Tighten screw firmly. 4. Turn adjusting screw counterclockwise (see Figure 4). Continue to turn adjusting screw until adjusting block is to rear of adjusting plate. 5. Install guide bar onto saw body. Place rear of guide bar between adjusting plate and sprocket support. IMPORTANT:Make sure to insert adjusting block into oval adjusting hole on guide bar. 6. Line up holes on sprocket support with center slot on guide bar and holes in saw body. 7. Insert guide bar bolts through front hand guard, saw body, center slot of guide bar, and sprocket support. Attach guide bar nuts to guide bar bolts. IMPORTANT:Tighten guide bar nuts finger tight only. Make sure adjusting block is in oval adjusting hole on guide bar. 8. Place chain around drive sprocket, then along top groove of guide bar and around guide bar nose. Note: Make sure cutting edges of chain are facing the right direction. Position chain so cutting edges on top of guide bar face CAUTION: Do not place chain on saw backwards. If chain is backwards, saw will vibrate badly and will not cut. 9. Adjust saw chain tension. Follow steps guide bar nose (see Figure 3). under Saw Chain Tension Adjustment, page 7. Tapping Front Hand Mounting Stand-Outs Guide Bar Bolts Guide Bar Nuts Adjusting Hole Guide Bar Screw Saw ChainCutting Edge Cutting Edge Towards Guide Bar Nose Guard Drive Sprocket Figure 3 - Assembling Guide Bar, Chain, and Hand Guard Adjusting Block Adjusting Plate Adjusting Screw Sprocket Support Figure 4 - Part Locations For Assembling Guide Bar 6 097017 097017 7 OWNER’S MANUAL PUSH TO SHARPEN INSTALLING AUTOMATIC CHAIN SHARPENER (Fast Sharp Models Only) 1. Screw automatic chain sharpener into threaded hole. 2. Continue turning automatic chain sharpener until you hear five (5) clicks. Automatic Chain Sharpener Figure 5 - Automatic Chain Sharpener (Fast Sharp Models Only) ASSEMBLY Continued Note: For pre assembled models, the saw chain tension is properly set at factory. A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Follow steps below to readjust saw chain tension. 1. Before adjusting chain, make sure guide bar nuts are only finger tight (see Figure 3, page 6). Also make sure adjusting block is in oval adjusting hole on guide bar (see Figures 3 and 4, page 6). 2. Turn adjusting screw clockwise until all slack is out of chain (see Figure 6). Note: There should be no gap between side links of chain and bottom of guide bar (see Figure 7). 3. Wearing protective gloves, move chain around guide bar. Chain should move freely. If chain does not move freely, loosen chain by turning adjusting screw counterclockwise. 4. After chain tension is correct, tighten guide bar nuts firmly. If not, guide bar will move and loosen chain tension. This will increase the risk of kickback. This can also damage saw. Note: A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Readjust chain tension. SAW CHAIN TENSION ADJUSTMENT WARNING: Unplug chain saw from power source before adjusting saw chain tension. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. WARNING: Maintain proper chain tension always. A loose chain will increase the risk of kickback. A loose chain may jump out of guide bar groove. T...

Herunterladen

Geben Sie zwei Ziffern: