Stimmen - 3, Durchschnittliche Bewertung: 3.3
(
)
)
|
Anleitung Zusammenfassung
It is your guide to safe and proper operation of this chain saw. ENGLISH 107705 5 6 107705 CHAIN SAW NAMES AND TERMS Bucking Process of cutting a felled tree or log into lengths. Chock Block or wedge used to secure wood from moving. Felling Process of cutting down a tree. Felling Cut Final cut when felling a tree. Make this cut on opposite side of tree from notching cut. Front Handle Located at front of saw body. Front Hand Guard Shield between front handle and guide bar. Protects left hand while using saw. Guide Bar Metal bar that extends from saw body. The guide bar supports and guides chain. Guide Bar Nose Tip or end of guide bar. Kickback Quick backward and upward motion of guide bar. Kickback may occur when tip of guide bar touches an object while chain is moving. The guide bar will kick up and back towards operator. Limbing Process of cutting limb(s) from a felled tree. Low-Kickback Chain Chain that reduces chance of kickback as required by ANSI B175.1. Normal Cutting Position Stance used while making bucking and felling cuts. PRODUCT IDENTIFICATION Figure 2 - Chain Saw Model 107624-01, -02 Chain Tensioning Screw Rear Handle Power Cord Guide Bar Saw Chain Front Handle with Hand Guard Oil Cap Oil Level Sight Trigger Switch Lockout Cord Hitch Guide Bar Nose Figure 3 - Chain Saw Model 107625-01, -02, 111174-01 Rear Handle Power Cord Guide Bar Saw Chain Front Handle with Hand Guard Oil Cap Oil Level Sight Trigger Switch Lockout Chain Tensioning Knob Cord Hitch Guide Bar Nose UNPACKING 1. Remove all items from carton. 2. Check all items for any shipping damage. If you find any damage or if any parts are missing, call Technical Services at 1-800-858-8501 for prompt service. Notching Cut Notch cut in tree that directs fall of tree. Oiler Control System for oiling guide bar and chain. Power Head Chain saw without chain and guide bar. Also known as saw body. Pushback (Kickback, Pinch) Rapid pushback of chain saw. Pushback may occur if chain along top of guide bar is pinched, caught, or contacts a foreign object. Rear Handle Handle located at rear of saw body. Reduced Kickback Guide Bar Guide bar that reduces chance of kickback. Replacement Chain Chain that complies with ANSI B175.1 when used with a specific saw. It may not meet ANSI requirements when used with other saws. Saw Chain (Chain) Loop of chain having cutting teeth for cutting wood. The motor drives chain. The guide bar supports chain. Spiked Bumper (Spike) Pointed teeth at front of saw body beside guide bar. Keep spiked bumper in contact with wood when felling or bucking. It helps maintain position of saw while cutting. Sprocket Toothed wheel that drives chain. Switch Device that completes or interrupts electrical circuit to motor of saw. CHAIN SAW NAMES AND TERMS Continued Switch Linkage This device connects switch to trigger. It moves switch when you squeeze trigger. Switch Lockout Device that reduces accidental starting of saw. Trigger Device that turns saw on and off. Squeezing trigger turns saw on. Releasing trigger turns saw off. Trimming (Pruning) Process of cutting limb(s) from a living tree. Undercut An upward cut from underside of log or limb. This is done while in normal cutting position and cutting with top of guide bar. ASSEMBLY Note: Some models are pre-assembled. Assembly is not needed on these models. See Saw Chain Tension Adjustment, pages 8 and 9. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. IMPORTANT: Do not clamp chain saw in vise during assembly. 1. Lay chain out flat. 2. Loosen and remove guide bar nuts and sprocket cover. 3. Loosen and remove drive sprocket screw or remove E-ring from shaft (see Figure 4). Remove sprocket support. 4. Install guide bar onto saw body. Assemble center slot of guide bar onto guide bar bolts. 5. To replace sprocket support, repeat step 3 in reverse order. Firmly tighten drive sprocket screw with #2 Phillips screwdriver (if applicable). 6. Place chain around drive sprocket, along top groove of guide bar, and around guide bar nose. Note: Make sure cutting edges of chain are facing in right direction. Position chain so cutting edges on top of guide bar face guide bar nose (see Figure 4, and indicator on side cover of saw). CAUTION:Do not place chain on saw backwards. If chain is backwards, saw will vibrate badly and will not cut. 7. Insert tab of sprocket cover into slot on side cover and rotate sprocket cover onto guide bar bolts until sprocket cover rests against guide bar. 8. Place guide bar nuts, removed in step 2, over guide bar bolts. IMPORTANT: Tighten guide bar nuts finger tight only. 9. Turning chain tensioning knob (Model 10762501, -02, 111174-01) or chain tensioning screw (Model 107624-01, -02), adjust position of adjustment block until it is aligned and inserted into the round adjusting hole on guide bar (see Figure 4 and Figures 5 and 6, page 8). Turning chain tensioning knob or chain tensioning screw counterclockwi...
Dieses Handbuch ist für folgende Modelle:Kettensägen - 107624-02 (3.81 mb)
Kettensägen - 107625-02 (3.81 mb)
Kettensägen - 11174-01 (3.81 mb)