Stimmen - 4, Durchschnittliche Bewertung: 3.5
(
)
)
|
Anleitung Zusammenfassung
. Keep gasoline and oil away from the eyes. If gasoline or oil comes in contact with the eyes, wash them immediately with clean water. If irritation is still present, see a doctor immediately. . Clean up spilled fuel immediately. Refer to Refueling in the Specific Safety Rules section of this manual for additional safety information. MIXING THE FUEL . This product is powered by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle oil. Pre-mix unleaded gasoline and 2-cycle engine oil in a clean container approved for gasoline. . This engine is certified to operate on unleaded gasoline intended for automotive use with an octane rating of 87 [(R + M) / 2] or higher. .. Do not use any type of pre-mixed gasoline/oil from fuel service stations, this includes the pre-mixed gasoline/oil intended for use in mopeds, motorcycles, etc. .. Use a high quality 2-cycle self-mixing oil for air-cooled engines. Do not use automotive oil or 2-cycle outboard oil. .. Mix 2% oil into the gasoline. This is a 50:1 ratio. . Mix the fuel thoroughly and each time before fueling. .. Mix in small quantities. Do not mix quantities larger than usable in a 30-day period. A 2-cycle oil containing a fuel stabilizer is recommended. PREMIUM EXACT MIX™ (50:1) GASOLINE OIL 1 Gallon (US) 2.6 oz. 1 Liter 20 cc (20 ml) OXyGENATEd FUELS Some conventional gasolines are blended with alcohol or an ether compound. These gasolines are collectively referred to as oxygenated fuels. To meet clean air standards, some areas of the United States and Canada use oxygenated fuels to help reduce emissions. If using an oxygenated fuel, make sure it is unleaded and meetstheminimumoctaneratingrequirements.Beforeusing an oxygenated fuel, try to confirm the fuel’s contents. Some states/provinces require this information to be posted on the pump. The following are the EPA approved percentages of oxygenates: Ethanol (ethyl or grain alcohol) 10% by volume. You may use gasoline containing up to 10% ethanol by volume. Gasoline containing ethanol may be marketed under the name “Gasohol.” Do not use E85 fuel. MTbE (methyl tertiary butyl ether) 15% by volume. You may use gasoline containing up to 15% MTBE by volume. Methanol (methyl or wood alcohol) 5% by volume. You may use gasoline containing up to 5% methanol by volume as long as it also contains cosolvents and corrosion inhibitors to protect the fuel system. Gasoline containing more than 5% methanol by volume may cause starting and/or performance problems. It may also damage metal, rubber, and plastic parts of the product or your fuel system. Ifyounoticeanyundesirableoperatingsymptoms,tryanother service station or switch to another brand of gasoline. NOTE: Fuel system damage or performance problems resulting from the use of an oxygenated fuel containing more than the percentages of oxygenates stated previously are not covered under warranty. Page 11 Page 12 FILLING THE fuel TANK See Figure 2. n Clean the surface around the fuel cap to prevent contamination. n Loosen the fuel cap slowly. n Carefully pour the fuel mixture into the tank. Avoid spillage. n Prior to replacing the fuel cap, clean and inspect the o-ring. n Immediately replace the fuel cap and hand tighten. Wipe up any fuel spillage. Note: It is normal for the engine to emit smoke during and after the first use. ADDING bar and chain OIL See Figure 3. Use HOMELITE Bar and Chain Oil. It is designed for chains and chain oilers, and is formulated to perform over a wide temperature range with no dilution required. Chain saw should use approximately one tank of oil per tank of fuel. Note: Do not use dirty, used, or otherwise contaminated oils. Damage may occur to the oil pump, bar, or chain. n Carefully pour the bar and chain oil into the oil tank. n Fill the oil tank every time you fuel the engine. OPERATING THE CHAIN BRAKE See Figures 4 - 5. Check the operating condition of the chain brake prior to each use. n Using the back of your left hand, engage the chain brake by pushing the chain brake lever/hand guard toward the bar while the chain is rotating rapidly. n Reset the chain brake back into the RUN position by grasping the top of the chain brake lever/hand guard and pulling toward the front handle until you hear a click. WARNING: If the chain brake does not stop the chain immediately, or if the chain brake will not stay in the run position without assistance, take the saw to an authorized service center for repair prior to use. operation Fig. 2 Fig. 3 Fig. 4 Fig. 5 Run Position Brake Position Page 13 operation STARTING THE ENGINE See Figures 6 - 11. Starting the product differs depending on whether the engine is cold or warm. WARNING: Keep your body to the left of the chain line. Never straddle the saw or chain, or lean over past the chain line. n Place the chain saw on level ground and ensure that no objects or obstructions are in the immediate vicinity that could come in contact with the bar and chain. n Hold the front handle firmly with your left hand a...
Dieses Handbuch ist für folgende Modelle:Kettensägen - UT10516/16 IN. 33CC (3.52 mb)