Stimmen - , Durchschnittliche Bewertung: ( )

Anleitung Remington Power Tools, modell M30016US

Hersteller: Remington Power Tools
Dateigröße: 2.7 mb
Dateiname:

Unterrichtssprache:

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Das Dokument wird geladen, bitte warten

HerunterladenSchließen

Remove oil cap. 2. Fill oil tank with SAE #30 motor oil. Note: For temperatures below 30°F, use SAE #10 oil. For temperatures above 75°F, use SAE #40 oil. DO NOT use standard bar and chain oil. 3. Replace oil cap at once. Tighten oil cap firmly for good seal. This will avoid oil seepage from cap. 4. Wipe off excess oil. Note: It is normal for oil to seep when saw is not in use. It is necessary to empty oil tank after each use to prevent seepage. OILING CHAIN Manual Oil System Always check oil level before using saw. Do not attempt to operate the oil system while saw is in operation. To oil chain, press squeeze bulb. Oil will feed onto the guide bar and chain. Press squeeze bulb at least once before each cut. Check oil level often by looking at oil level through side of oil bottle (see Figure 9). Oil Squeeze Bulb Oil Bottle Figure 9 - Oil Squeeze Bulb and Oil Bottle Location CLEARING SPROCKET COVER OF DEBRIS While operating the chain saw, wood chips, small twigs, and other debris can occasionally build up inside the sprocket cover. To properly maintain the saw and keep it in good working order, periodic removal of this debris may be required. To properly clear debris from the sprocket cover: 1. Unplug chain saw. 2. Loosen and remove guide bar nut (see Figure 10). 3. Turn chain tensioning screw counterclockwise to loosen chain until sprocket cover is easily removed. 4. After sprocket cover is removed, clear all chips, twigs, and debris. WARNING: Use caution when clearing debris that is around chain. Cutting edges on chain are sharp. Use protective gloves when working around or handling chain. 5. Once debris has been removed, follow steps 7 through 13 on pages 9 and 10 in the Assembly section to re-assemble the sprocket cover to the chain saw. Wood Chips, Twigs, and Debris Sprocket Cover Guide Bar Nut Figure 10 - Removing and Clearing Sprocket Cover of Debris ENGLISH 13 EXTENSION CORDS Use proper extension cords with this saw. Use only extension cords marked for outdoor use. The cord must be marked with suffix W or W-A following the cord type designation. Example: SJTW-A or SJTW. Use proper sized cord with this saw. Cord must be heavy enough to carry current needed. An undersized cord will cause voltage drop at saw. Saw will lose power and overheat. Follow cord size requirements listed below. Cord Length AWG Cord Size 25 feet 16 AWG 50 feet 16 AWG 100 feet 16 AWG 150 feet 14 AWG Models: M15012US, M15014AS Cord Length AWG Cord Size 25 feet 16 AWG 50 feet 16 AWG 100 feet 14 AWG 150 feet 12 AWG Models: M30016US, M30016AS, M30016AW, M35016AW Keep cord away from cutting area. Make sure cord does not catch on branches or logs during cutting. Inspect cords often. Replace damaged cords. This chain saw is designed with an extension cord hitch that prevents the extension cord from being pulled loose during use. To use, form a loop with the end of the extension cord, insert loop into slot in rear of handle, and place loop over cord hitch (see Figure 11. Gently pull loop against cord hitch until slack is removed. Plug extension cord into chain saw cord. Power Cord Extension Cord Cord Hitch Figure 11 - Looping Extension Cord over Cord Hitch CUTTING WITH THE CHAIN SAW 1. Connect saw to extension cord. Connect extension cord to power supply. 2. Make sure section of log to be cut is not laying on ground. This will keep chain from touching ground as it cuts through log. Touching ground with moving chain will dull chain. 3. Use both hands to grip saw. Always use left hand to grip front handle and right hand to grip rear handle. Use firm grip. Thumbs and fingers must wrap around saw handles (see Figure 12). 4. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet. 5. When ready to make a cut, push the lockout button completely forward with the right thumb and squeeze the trigger (see Figure 12). This will turn saw on. Releasing trigger will turn saw off. Make sure saw is running at full speed before starting a cut. 6. When starting a cut, place moving chain against wood. Hold saw firmly in place to avoid possible bouncing or skating (sideways movement) of saw. 7. Guide saw using light pressure. Do not force saw. The motor will overload and can burn out. It will do the job better and safer at the rate for which it was intended. 8. Remove saw from a cut with saw running at full speed. Stop saw by releasing trigger. Make sure chain has stopped before setting saw down. 9. Practice until you can maintain a steady, even cutting rate. Trigger Switch Lockout Button Figure 12 - Lockout Button and Trigger Location 14 Hinge 2" (5 cm) 2"(5 cm) 2nd Cut 1st Cut Lower Notch Cut 3rd Cut - Felling Cut Hinge 2" (5 cm) 2"(5 cm) 2nd Cut 1st Cut Lower Notch Cut 3rd Cut - Felling Cut OPERATING CHAIN SAW ENGLISH FELLING A TREE (Cutting Down a Tree) WARNING: • Avoid kickback. Kickback can result in severe injury or death. See Kickback to avoid risk of kickback. • ...