Stimmen - 1, Durchschnittliche Bewertung: 5 ( )

Hersteller: Black & Decker Dateigröße: 991.21 kb Dateiname: Unterrichtssprache:

+40.C +10.C Charge only at ambient temperatures between 10°C and 40°C. The charger is intended for indoor use only. Your charger is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. Electrical safety Your charger is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard. Warning! Never attempt to replace the charger unit with a regular mains plug. Features 1. On/off switch 2. Lock-off button 3. Oil cap 4. Oil reservoir 5. Front guard assembly 6. Chain cover assembly 7. Chain tension adjustment screw 8. Chain 9. Guide bar 10. Battery 11. Chain sheath 12. Charger receptacle 13. Charger Assembly Warning! Before assembly, remove the battery (10) from the tool. Fitting and removing the battery (fig. A) . To fit the battery (10), line it up with the receptacle on the tool. Slide the battery (10) into the receptacle and push until the battery (10) snaps into place. . To remove the battery (10), push the release button (24) while at the same time pulling the battery (10) out of the receptacle. Warning! To prevent accidental operation, make sure that the battery is removed and that the chain sheath (11) is in place on the saw chain (8) before performing the following operations. Failure to do this could result in serious personal injury. Charging the battery (fig. B and C) The battery (10) needs to be charged before first use and whenever it fails to produce sufficient power on jobs that were easily done before. When charging the battery (10) for the first time, or after prolonged storage, it will only accept an 80% charge. After several charge and discharge cycles, the battery (10) will attain full capacity. The battery (10) may become warm while charging; this is normal and does not indicate a problem. Warning! Do not charge the battery at ambient temperatures below 10°C or above 40°C. Recommended charging temperature: approx. 24°C. 8 hour charger (fig. B) . To charge the battery (10), remove it from the tool and slide the charger receptacle (12) onto the battery (10). . Plug in the charger (13). 9 The battery (10) will be fully charged in approximately 8 hours. It can be removed at any time or left in the connected charger indefinitely. 1 hour charger (fig. C) . To charge the battery (10), remove it from the tool and insert it into the charger (23). The battery (10) will only fit into the charger (23) in one way. Do not force. Be sure that the battery (10) is fully seated in the charger (23). . Plug in the charger (23). . Check that the red charging indicator comes on. If the green ‘end of charge’ indicator comes on then the battery is too hot and cannot be charged. If this happens, remove the battery (10) from the charger (23), let the battery cool down for approximately 1 hour and re-insert it. After approximately 1 hour of charging, the red charging indicator will go off and the green ‘end of charge’ indicator will come on. The battery is now fully charged. . Remove the battery (10) from the charger (23). Installing and removing the saw chain (fig. D - F & H) Always wear protective gloves when installing or removing the saw chain (8). The saw chain (8) is sharp and can cut you when it is not running. . Place the tool on a firm and stable surface. . Loosen the 2 Allen screws (14) using the Allen key (21) provided. Remove the Allen screws (14). . Remove the chain cover assembly (6). . Turn the chain tension adjustment screw (7) counter clockwise to allow the guide bar (9) to recede and to reduce the tension on the saw chain (8). . Remove the old saw chain (8) from the sprocket (15) and the guide bar (9). . Place the new saw chain (8) in the groove of the guide bar (9) and around the sprocket (15). Make sure that the teeth are facing the correct direction by matching the arrow on the saw chain (8) with the arrow on the chain cover assembly (6). . Make sure that the slot (17) in the guide bar (9) is over the location pins (18) and that the hole (20) below the slot is located over the adjustment pin (19). . Fit the chain cover assembly (6) and the 2 Allen screws (14). . Tighten the Allen screws (14) using the Allen key (21) provided. . Adjust the chain tension as described below. Checking and adjusting the chain tension (fig. D and G) . Check the saw chain tension. The tension is correct when the saw chain (8) snaps back after being pulled away 3 mm from the guide bar (9) with light force from the middle finger and thumb. There should be no ‘sag’ between the guide bar (9) and the saw chain (8) on the underside. To adjust the tension: . Loosen the 2 Allen screws (14). . Turn the chain tension adjustment screw (7) clockwise. Warning! Do not over-tension the chain as this will lead to excessive wear and will...

Herunterladen

Geben Sie zwei Ziffern: