Stimmen - 5, Durchschnittliche Bewertung: 3.8
(
)
)
|
Anleitung Zusammenfassung
• Make sure there is a second person within calling distance. • The working area should be free from obstacles. • Wear suitable clothes which do not hinder movement. • Use specific prodections during operations involving head, hands, feet, eyes and ears. • It is recommended the use of a helmet with a visor during felling, branch cutting and chopping operations. • Wear gloves with an external protection when using the electric chain saw. • Use ear protection to prevent hearing injuries. • Wear safety boots when using the electric chainsaw. Know your product 1. Front handle 2. Front hand guard 3. Oil tank cap 4. Chain clamp/lock knob 5. Chain 6. Bar 7. Power cord 8. Rear handle 9. Chain wheel 10.Bar adjustment block 11.Cover 12. Bucking spikes 13.On/off switch 14.Lock-off button (not shown) 715.Barcover16.Oillevelindicator17.Cordretentionhook56413782131510161291117 Mounting the chain bar 1. Place the chainsaw with the motor on a cover to avoid any mess from the oil. 2. Place the chain (5) in the grove of the bar (6). Pay attention to the correct running direction. As shown by the running direction symbol. 3. Place the chain links around the chain wheel (9) and put the bar on such that the two locating pegs fit into the slotted hole of the bar. 4. Prior to fitting the cover (11) it is important to set the chain adjusting cam. To do this fully depress the chain clamp/lock knob and rotate until the cam is aligned with the arrow as pictures in Fig 1. 5. To fit the cover (15) insert the back locating hook into the slot provided near the oil indicator and lower the cover over the bar ensuring the clamp bolt of the cover passes through the centre of the bar adjustment block (10) and rotate the clamp/lock knob until it just starts to become tight. Note. Do not push the clamp/lock knob while rotating. Proceed as detailed below to set the chain tension. Fig1 Setting the chain saw tension 1. Loosen the chain clamp/lock knob by turning it anti-clockwise approximately 1-2 turns. 2. Press the chain clamp/lock knob inwards and turn it in a clockwise direction until the correct chain tension is reached. 3. The correct tension is reached when the chain in the middle of the bar can only be raised by approximately 3-4mm. 4. Release the chain clamp/lock knob and ensure it springs away from the housing slightly. 5. Tighten the chain clamp/lock knob by turning it clockwise without pressing it inwards. 6. Check whether all chain links lie correctly in the guide tracks of the bar. Oil filling Note. The chain saw is shipped without oil in it. The chain saw must never be used without oil or with an oil level that is below the indicator. Warning. Always ensure that the chainsaw is switched off and the plug is removed from the power point before making any adjustments. 1. Remove oil tank cap (3) and fill the tank with chain oil. Replace the oil tank cap and tighten well. 2. Lubrication is activated only when the machine is working. 6. Screw in the chain clamp/lock knob tightly. 3. Check the oil level periodically, through the oil level indicator (16). 8 4. Use good quality ecological chain oil to ensure long life for the moving parts. Do not use recovered or preused oil containing impurities. Make sure that no dirt gets into the oil tank. Checking the automatic oil function Check the automatic operation of the chain lubrication by pointing the tip of the switched-on saw towards a piece of paper laying on the ground. If a patch of oil appears and becomes larger, then the automatic oil function is working. If there are no traces of oil even though the oil tank is full, then the automatic oil function is not working. If the automatic oil function is not working, remove the chain bar and clean out the oil ways of the chainsaw and chain bar. On reassemble if the chainsaw is still not working take it to an autorised service centre. Avoiding kickback • Be constantly aware of the position of the upper quadrant of the blade tip. This is the part that triggers a kickback when it hits resistance. • Never engage the upper quadrant of the guide bar with whatever you are cutting and avoid contact with any hidden branches or obstructions. Ensure there is a clear work area. • Always clear away brush, vegetation and any obstructing debris before attempting a cut that might trigger a kickback. • Avoid cuts that will cause the chainsaw to jam in a tree trunk or limb. Avoid jamming Always cut into the compression wood first until the cut starts to close. Always make the compression cut beneath if the log or limb is suspended from one end, and on top if it is supported at both ends. Cut from the other side towards the compression cut. Make a habit of using a wedge to prevent the compression cut jamming tight on the chainsaw blade. Extension cord support During use of the chainsaw, the extension cord will continually be pulled as you move from one area to another. A cord retention hook (17) has been provided on the housing of the chainsaw to assist in preven...