Stimmen - 5, Durchschnittliche Bewertung: 4.2 ( )

Hersteller: Pentair Dateigröße: 1.56 mb Dateiname: Unterrichtssprache:

The handle will remain fixed in this position. Repeat this process on the other side of the cleaner. Remember, the handle must be fixed diagonally, see Figures 4 and 5. 4. Place the unit in the water. Turn the unit side to side in the water to allow air to escape from the body and then let the cleaner sink to the bottom of the pool, see Figure 6. Then, spread the cable over the surface of the pool as evenly as possible as shown in Figure 2. 5. Plug the cable into the power supply. Make sure the key on the plug exactly corresponds with the key slot on the socket of the power supply, see Figure 7. Plug the power supply into a grounded outlet. Make sure that the electric outlet has been properly grounded, see Figure 8. The light will glow indicating that the system is “ON” and the pool cleaner will start the cleaning cycle. The unit keeps record of the number of cleaning cycles. Only an authorized service center can display the accumulated cleaning cycles. (See details on the next page.) Figure 7. Transformer Plug Transformer Socket Figure 8. 10 ft. / 3m Handle Lock Mechanism Figure 2. Figure 3. Figure 5. Figure 6. Figure 4. Prowler™ 720 and 730 Installation and User’s Guide 6 Prowler™ 720 and 730 Installation and User’s Guide Setting Up the Standard Power Supply (Transformer) To plug the cable into the transformer socket on the power supply, follow these steps: 1. Prepare the plug with the key and three outside slots as shown in Figure 9. 2. Fit the key and the slots from cable plug exactly with the corresponding key and slots from the transformer socket. 3. Push the plug all the way into the socket of the transformer. 4. Once the plug is in, rotate the plug to the right to lock it into place as shown in Figure 9. 5. To remove the plug, first rotate the plug to the left to unlock it, then pull it out. 6. The Power Supply (Transformer) is now ready for operation. Listed below are the Transformer buttons as shown in Figure 10: a. Green Button: push button turns the machine ”ON”. b. Red Button: push button turns the machine “OFF”. IMPORTANT– After every cycle, the pool cleaner will turn off automatically. In case you want to turn the machine off during the working cycle, push the red button once and the indicator light will turn off signaling that the machine has stopped running. Figure 9. Figure 10. (Remember to keep the Power Supply at least 10 feet away from the pool.) Push and rotate right to lock Transformer Socket Transformer Cable Plug Transformer Socket Cable Plug Rotate left and pull to unlock b a Wireless Remote Control -only for Prowler™ 730 cleaners equipped with Remote Control Using Radio Remote Control Feature and Accessing Cleaning Modes The Remote Control Model is equipped with a multi-directional radio transmitter, see Figure 12. This feature will enable you to guide the pool cleaner directly to areas of the pool requiring additional cleaning attention or for quick clean-ups. When you Forward / Reverse press the Right or Left buttons, the cleaner will turn until the button is released. Then, the cleaner will proceed straight ahead Right in the new direction. Pressing the Forward/Reverse button will cause the cleaner to proceed in the new direction after the button Left has been released. LED Cleaning Modes Program The Remote Control has an advanced cleaning program with two options: Option 1: STANDARD MODE — this cycle is 1. hours long and cleans the bottom of the pool only. Option 2: SUPER MODE — this cycle cleans the bottom and the walls of the swimming pools. This cleaning program is 3 hours long and is registered in the cycle counter as two cycles (one for each 1.5 hours of use). Every time a cleaning cycle is complete Figure 12. the cleaner will stop automatically. Every remote control unit is shipped from the factory with the “Standard Mode” as the primary program. To switch from the “Standard Mode” to the “Super Mode”, simply press the "Program" button once. The cleaner will immediately receive the command and will start to clean the bottom and the walls. Your signal that the cleaner is in the “Special Mode” is that the machine will climb up to the waterline in the first contact with a wall. To return to the “Standard Mode”, simply press the “Program” button again, ONLY when the machine is on the pool bottom. NOTE: When the Power Supply is turned off, the Mode is automatically returned to the "Standard Mode" (floor cleaning only). CAUTION — Be sure to always keep your Pentair pool cleaner properly stored anywhere between 50° to 104° Fahrenheit, (10° to 40° Celsius). This will keep the motors, plastics and seals protected. Failure to comply will result in loss of warranty. Prowler™ 720 and 730 Installation and User’s Guide Replacing the Remote Control Battery 1. Remove the top screw (see Figure 13, Step 1). 2. Pull the top of the cover away from the transmitter and then pull upwards (Step 2). 3. Replace the battery and make sure the polarity is the same as the existing battery (Step 3). 4....

Herunterladen

Geben Sie zwei Ziffern: