Stimmen - 4, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: AquaPRO Dateigröße: 1.31 mb Dateiname: Unterrichtssprache:

The chlorinator must be downstream of the heat pump. Failure to do so may void the warranty. If you have an in-floor cleaning system, please take note of any special plumbing requirements to operate all units effectively. Figure 2 shows the recommended installation layout. ! CAUTION PRO400, PRO600, PRO1000 5’ Minimum 18” Min. 18” Min. 36”Min. 18” Min. Figure 1 - Unit Location Figure 2 - Recommended installation layout FILTER POOL PUMP CHLORONATOR WARM WATER OUT TO POOL COLD WATER IN FROM POOL IN OUT CHECK VALVE 1-877-AQUASYS UNIONS (INCLUDED WITH PRO1000) 4 Basic Heat Pump Operation Electrical Connections All wiring and electrical connections must be performed by a qualified electrician. Installations must be in accordance with local and national codes. Overheating, shortcircuiting and fire damage will result from inadequate wiring. All units are equipped with an electrical wiring schematic inside the electrical panel. If this is missing, please contact the factory at 1-877-278-2797 to obtain one. All units are to be wired for 230 VAC, 1 phase. Please see following chart for correct amperage: Pool Heater is to be installed in accordance with Article 680 of the National Electrical Code (NEC), NFPA 70, and within the requirements of all local codes having jurisdiction. ! CAUTION ! WARNING Figure 3 - PRO400 & PRO600 Wiring Diagram See Figure 3 for wiring schematic of PRO400 & PRO600. See Figure 6 for wiring schematic of PRO1000. Connecting to Remote System (PRO1000 only) The PRO1000 Pool Heater is compatible with all known remote systems in the pool industry. If you have or add a remote system to your pool, please review these instructions for wiring and setting the thermostats on your pool heat pump. You will need to know if your remote system is a 2 wire or a 3 wire system. For 2 wire remotes 1. Turn the “pool” and “spa” thermostat up to their highest settings 2. Switch the toggle to “off” setting 3. See figure 4 for wiring diagram of 2 wire remote system 4. Connect remote system’s 2 wires to the 4 & 5 positions on the terminal block. For 3 wire remotes 1. Turn the “pool” thermostat to the desired pool temperature. 2. Turn the “spa” thermostat to the desired spa temperature 3. Switch the toggle to the “off” setting. 4. See figure 5 for wiring diagram of 3 wire remote system 5. Connect the low (or pool) wire to position 4 on the terminal block. Operating Instructions Figure 4 - Connecting to a 2 wire remote system SWITCH Yellow Blue Figure 5 - Connecting to a 3 wire remote system SWITCH Yellow Blue High Common (Spa) Low (Pool) 6. Connect the high (or spa) wires to position 6 on the terminal block. 7. Connect the common wire to position 5 on the terminal block. Gray Gray P S 1-877-AQUASYS BREAKER OR FUSE HEAT PUMP PRO400 20-amp PRO600 30-amp PRO1000 50-amp that power to the unit is on. The RED light indicates that the unit is in heating mode. • The RED light may become illuminated prior to heater start up. The RED light will become lit when the thermostat knob is set at or above the water temperature. • The unit has a built in time delay. Every time the unit turns off there is a five-minute time delay until the unit may be restarted. The HEAT light may turn on during this delay cycle. Do not rotate the thermostat knob during this time delay. Rotating the knob during this cycle may reset the time delay, causing the unit to wait an additional five minutes prior to startup. Water Temperature Set Point • Temperature set point range is 45°F to 107°F. Rotating the thermostat knob clockwise will increase the temperature set point, while rotating counterclockwise will decrease the temperature set point. • A floating thermometer may be placed in the pool or spa to monitor water temperature. • To initially calibrate the thermostat to the desired set point, turn the thermostat knob fully clockwise. The unit will turn on and begin heating after a possible five minute time delay. Allow the unit to run until pool or spa water reaches the desired temperature. Slowly turn thermostat knob counterclockwise until the unit turns off. The unit will now maintain this water temperature, providing the circulation pump is running. Application Guidelines Maintenance All heat pumps are designed for outdoor use. However, some maintenance is required to maintain the full life of the heater and is necessary to maintain your warranty. Annual maintenance should be scheduled to make sure blowing sand or falling debris is removed from the inside of the heater. Rinsing the coil down monthly with low water pressure will help keep the base of the unit clear of debris. Do not use a high pressure washer. This can cause damage to your evaporator coils and will void your warranty. It is recommended that a licensed air conditioning specialist perform the annual planned maintenance on your heater. Manual Temperature Controls Description - PRO400 & PRO600 • The manual Temperature Control is designed to regul...

Herunterladen

Geben Sie zwei Ziffern: