Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
The Polaris climbs best in pools without sharp angles or curves in the transition from the pool floor to the pool wall. Approximately every three minutes the Polaris 380 goes into back-up mode. This action pulls the Polaris away from pool obstacles and increases its random pattern. Thrust Jet Adjustment The thrust jet powers the direction of the Polaris. Factory position is eleven o’clock, but depending on the pool, other settings are helpful. Sweep Hose Adjustment The sweep hose should move in a gentle sweeping motion. To increase or decrease its motion, turn off the booster pump and turn the sweep hose adjustment screw. See Troubleshooting for other action adjustments. PushesUnitLeftPushesUnitRight12693IncreasesClimbingDecreasesClimbing11 Routine Maintenance Cleaning the Filter Bag Remove the bag collar from the feed hose and depress the prongs to release the bag from the cleaner. Open the bag closure and dump out the debris. Velcro ClosureBag Collar Whenever possible, empty the filter bag when it is half full, especially if the dirt load is sand. It is easier to empty the filter bag when it is dry. Alternate between two filter bags. When one becomes full, remove it and put on the clean bag. Backwashing the Pool Filter Always disconnect the Polaris from the pool wall before cleaning or backwashing the pool filter. After cleaning or backwashing, let the filtration system run for at least five minutes to flush out the return lines before reconnecting the Polaris. Storage and Winterizing Never store the Polaris in direct sunlight. When storing for the winter, drain out all the water (freeze damage is not covered under the warranty). Remove the UWF from the pool wall by attaching the Quick Disconnect and using pulling pressure to unscrew. In some cases, it may be necessary to use the UWF Removal Tool (part #10-102-00) available from an authorized Polaris dealer. Serial NumberShown fromopposite side. 1373458769521017131112159113334115181941530351436202123222428292725263163457PoolWallToThePolaris4142434840444546474950515554534852525356 10-Foot Hose10-foot Leader Hose1611 10-Foot Hose3938321111 Exploded Parts Diagram English Exploded Parts Diagram English No. Part #Description Qty No. Part #Description Qty No. Part #Description Qty 1 2 3 9-100-1014 9-100-1152 9-100-1114 All-Purpose Bag* Housing, Turbine Upper Hub Cap 1 1 3 20 21 9-100-1116 C131 Wheel, Single-side 1 Thrust Jet Kit 1 40 41 42 10-112-00 6-500-00 9-100-9001 Restrictor Discs. Red and Blue 2 Universal Wall Fitting (UWF) 1 UWF Connector Assembly 122 23 24 9-100-7008 B20 B15 Sweep Hose Barb Complete 1 Adjustment Screw, Sweep Hose 1 Sweep Hose Attachment Clamp 1 4 5 6 9-100-5107 9-100-1108 C10 E-clip, Stainless Steel Ball Bearing Tire, MaxTrax® * 10 8 3 43 44 45 10-108-00 6-504-00 6-505-00 UWF Restrictor Kit 1 Filter Screen, UWF/QD 1 O-ring, UWF/QD 125 26 27 9-100-9004 9-100-7170 9-100-7009 Base Weight 1 Hose Clamp for WMS 6 Jet Retainer 2 7 8 9 9-100-1008 9-100-1017 9-100-7011 Wheel, Double-side Belt Kit, Small and Large Shield, Bearing 2 1 3 46 47 48 9-100-9002 D29 D15 Pressure Relief Valve, Black 1 Quick Disconnect, UWF 1 Hose Nut 1028 29 30 9-100-7010 9-100-1155 9-100-3105 Water Management (WMS) 1 Housing, Turbine Lower 1 Sweep Hose Scrubber* 1 10 11 12 13 14 15 16 17 18 9-100-1005 9-100-5125 9-100-1139 9-100-1010 B25 9-100-1007 9-100-5115 9-100-5130 9-100-1132 Frame Screw, 8-32 x 1/2" SS Axle Block Kit, Front & Rear Belt Divider, Transfer Pulley Orifice Tip with Tip Guard Trans Pulley/Drive Shaft Assy Screw, 8-32 x 3/4" SS Lock Washer, Axle Block Drive Train Gear Kit with Turbine Bearing 1 11 1 1 1 1 4 4 1 49 50 51 * D20 D10 Adapter Hose, 8-1/2" 1 Swivel, Ball Bearing 3 Float, Feed Hose 931 32 33 9-100-5132 9-100-7030 9-100-7003 O-ring, Feed Pipe 1 Top and Base Assembly 1 Feed Pipe/Timer Blank Assy 1 52 53 54 D45 D50 G52 Feed Hose, 10 Ft 2 Feed Hose, Leader, 10 Ft 1 Back-up Valve Kit 134 35 36 A20 B5 B10 Float, Head 1 Sweep Hose Complete* 1 Wear Rings* 8 55 56 57 G54 G57 G53 Case Kit for G52 1 Collar, Back-up Valve 1 Mechanism for G52 137 38 39 9-100-1018 9-100-1240 9-100-7028 Bag Collar 1 Top Housing 1 Bottom Assembly 119 9-100-1103 Turbine Wheel with Bearing 1 *Wear items not covered by warranty. English English Troubleshooting If the Polaris cleaner displays the following actions, adjustments may be necessary to restore performance. Refer to exploded parts diagram for part numbers indicated in parentheses. Action: Hangs up on steps or other obstacles for longer than 3 minutes. Solution: 1. Check the wheel RPM. 2. Verify the back-up valve (52) is cycling. 3. Adjust the thrust jet. 4. Remove unnecessary pool hardware or install a Ladder Guard Kit (order part #G21 from a Polaris dealer). Action: Polaris is sluggish, running with less power than normal. Solution: 1. Check the filter screen (#42) in the Quick Disconnect (#45) and clean, if necessary. 2. Clean the skimmer basket, pump basket, and pool filter. 3. ...