Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Part # Description Qty No. Part # Description Qty No. Part # Description Qty 1 2 3 K16 C40 K5 All-Purpose Bag* 1 Screw, 10-32 x 3/8" SS Pan 20 Top 1 20 21 C10 C6 Tire, MaxTrax®* 3 Wheel, Large (No Bearings Incl.) 3 39 40 41 9-100-1018 10-112-00 6-500-00 Bag Collar 1 Restrictor Disks, Red and Blue 1 Universal Wall Fitting (UWF) 122 23 24 C65 C131 C16 Axle, Large (Rear Wheel Only) 1 Thrust Jet Kit 1 Idler Wheel, Small 1 4 5 6 A20 9-100-3105 B25 Float, Head 1 Sweep Hose Scrubber* 1 Orifice Tip w/Orifice Tip Guard 1 42 43 44 9-100-9001 10-108-00 6-504-00 UWF Connector Assembly 1 UWF Restrictor Kit 1 Filter Screen, UWF/QD 125 26 27 C30 C32 C25 Screw, 4-40 x 3/16" SS Pan 1 Screw, 6-32 x 1/2" SS Pan Head 1 Spring for C36 1 7 8 9 B5 B10 B15 Sweep Hose Complete* Wear Rings* 8 Sweep Hose Attach Clamp 1 45 46 47 6-505-00 9-100-9002 D29 O-ring, UWF/QD 1 Pressure Relief Valve, Black 1 Quick Disconnect, UWF 128 29 30 C36 K10 K25 Swing Axle Kit 1 Base with Bracket 1 Water Management System 1 10 11 12 B20 K30 K20 Adjust. Screw, Sweep Hose 1 Feed Pipe with Elbow 1 Vacuum Tube 1 48 49 50 D15 ** D20 Nut, Feed Hose 10 Adapter Hose, 8-1/2" 1 Swivel, Ball Bearing 331 32 33 K145 C80 C83 Frame 1 Ball Bearings, Turbine 2 Turbine Shaft Tubes 1 13 14 15 C66 C76 C45 Axle, Large (w/Sand/Gravel Grd) 2 Screw, 10-32 x 7/8" SS Pan 10 Lock Washer for C36 7 51 52 53 D10 D45 D50 Float, Feed Hose 9 Feed Hose, 10 Ft 2 Feed Hose, Leader, 10 Ft 134 35 36 9-100-7170 A40 C86 Hose Clamp for WMS 2 Turbine Shaft Shield 1 Drive Shaft Assembly 1 16 17 18 C70 C60 C55 Axle Plate for C65/C66 3 Ball Bearings, Wheels 8 Wheel Screw, Plastic 4 54 55 56 G52 G54 G57 Back-up Valve Kit 1 Case Kit for G52 1 Collar, Back-up Valve 137 38 C120 C110 Hose for C110, 7-1/2" 1 Turbine Cover with Elbow 119 C64 Wheel Washer, Plastic 4 57 G53 Mechanism for G52 1 *Wear items not covered by warranty. English English Troubleshooting If the Polaris cleaner displays the following actions, adjustments may be necessary to restore performance. Refer to exploded parts diagram for part numbers indicated in parentheses. Action: Hangs up on steps or other obstacles for longer than 3 minutes. Solution: 1. Check the wheel RPM. 2. Verify the back-up valve (54) is cycling. 3. Adjust the thrust jet (#23). 4. Remove unnecessary pool hardware or install a Ladder Guard Kit (order part #G21 from a Polaris dealer). Action: Polaris is sluggish, running with less power than normal. Solution: 1. Check the filter screen (#44) in the Quick Disconnect (#47) and clean, if necessary. 2. Clean the skimmer basket, pump basket, and pool filter. 3. Check all of the hoses, connections, and swivels (#50) for leaks that could cause loss of water pressure. 4. Check the wheel RPM. Action: Polaris flies around the pool and/or does not make contact with the bottom. Solution: 1. Check the wheel RPM. If more than 32 RPM, unscrew the pressure relief valve (#46) to decrease water flow to cleaner. 2. Confirm that the blue restrictor disc is installed in the UWF to decrease water flow. Or, install the red restrictor disc to decrease water flow even more. Action: Solution: Action: Solution: Action: Solution: Action: Solution: 3. Verify the back-up valve (#54) is cycling. Hold the valve out of the water and watch the jet. It should come on and go off. Polaris does not back up. 1. Verify the back-up valve (#54) is cycling. 2. Check the wheel RPM. 3. If the bag (#1) is full, empty it. 4. If head float (#4) has water in it, replace it. 5. Make sure feed hose is floating. Polaris only turns in one direction. 1. Adjust the thrust jet (#23). 2. Make sure feed hose is floating. Feed hose becomes tangled. 1. Remeasure the hose to verify that it is adjusted to the proper length for the pool shape. 2. With the Polaris operating, check that the swivels (#50) in the hose and the hose connections turn freely. 3. Make sure feed hose is floating. 4. With the Polaris turned off, spin each of the wheels. All wheels should turn together. Sweep hose is sucked into the vacuum tube. 1. Make sure the opening at the end of the sweep hose (#7) is not blocked by the sweep hose scrubber (#5). 2. Adjust the sweep hose (#7) to a gentle sweeping motion. Action: Sweep hose sprays too much water out of the pool. Solution: 1. Adjust the speed of the sweep hose (#7) by tightening the adjustment screw (#10). 2. Replace the sweep hose scrubber (#5) if it is worn or missing. 3. Add a sweep hose weight (order part #B2) to keep the sweep hose from spraying. Action: The cleaner does not clean the entire pool. Solution: 1. Check the hose length reaches within 6” of the farthest point of the pool. If not, order a new hose section from your Polaris dealer. 2. Check thrust jet for straight back position that optimizes random turning. 3. While the cleaner is operating, hold it upside down and look into the vacuum tube. There should be two distinct, even jets of water. If there are not, contact Customer Service or a Polaris auth...