Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Unit must be submerged in water to operate properly. When not in use, store indoors in a clean, dry place. Do not leave underwater, in direct sunlight, or exposed to extreme temperatures. Make sure Robo-Kleen is unplugged from its power supply before cleaning, replacing the filter or any other routine maintenance. To protect risk of electrical shock, do not put the transformer in water or other liquid. To avoid damage to the transformer and cord, never carry the transformer by the cord or yank to disconnect from an outlet. Instead, disconnect by pulling the plug itself from the outlet. Do not pull cord around sharp corners or edges. !!! Do not operate with a damaged cord or transformer. Do not use with extension cord. Disconnect transformer from outlet when not in use. If cleaner is not working as it should or has been dropped or damaged in any way, contact SmartPool customer service before using. Congratulations on your purchase! You will find Robo- Kleen to be the most effective pool cleaner available. Unlike water-powered cleaners, which put all dirt and debris through your existing pool pump and filter, Robo-Kleen has its own pump and filter system. This saves you money in electricity costs and extends the life of your existing pool equipment. Read carefully before using your Robo-Kleen pool cleaner. Power Supply Connect to 110V GFCI Outlet Connect to the Cleaner Connect to Power On/Off Switch Mobile Cleaning Unit Filtered Water Outlet Drive Wheels Water Escape Door Side Handle 3 Power Supply Steering Wheels Underside of Mobile Cleaning Unit Locking Tabs Suction Ports Cleaning Brushes Installation The power supply should be positioned so that Robo-Kleen can reach all the walls of the swimming pool and must be at a minimum distance of 10 feet from the edge of the pool. CAUTION: INSURE THE THE 110V MAIN LINE OUTLET IS PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI) OR EARTH LEAKAGE CIRCUIT INTERRUPTER (ELCI). OTHERWISE, DEATH OR INJURY CAN RESULT. Locking Tabs ! DO NOT ALLOW POWER SUPPLY TO BECOME SUBMERGED IN POOL. DEATH OR INJURY CAN RESULT. DO NOT PLACE ON EDGE OF POOL. POWER SUPPLY MUST NOT FALL INTO POOL! To connect Robo-Kleen to the power supply, remove the cap on the transformer output socket. Plug the Robo-Kleen cord into the socket. Notice the plug and socket are indexed using pins. Tighten the threaded plug cover so that the cord is securely attached. Operation ! DO NOT ENTER THE SWIMMING POOL WHILE ROBO-KLEEN IS IN OPERATION TO AVOID ENTANGLEMENT WITH CORD a. Connect the cable to the power supply b. Grasp the cleaner by a side handle and place Robo-Kleen in the pool. c. Rock the unit from front to back and side to side, releasing trapped air, until the unit slowly sinks to the bottom of the pool. d. Start the unit at a 90° angle to a wall . CAUTION: BE SURE MAIN LINE OUTLET IS PROTECTED BY A GROUND FAULT CIRCUIT INTERRUPTER (GFCI) DEATH OR SERIOUS INJURY COULD OCCUR. e. Press the top of the On/Off switch through the clear jacket on the power supply. Robo-Kleen will take an initial 10 seconds to scan the circuit board and reset the memory. After the initialization is complete, filtered water will be pumped to the top and the unit will start moving. CAUTION: Do not operate Robo-Kleen out of the water. This may result in damage to the pump motor seals and invalidate the warranty. Optimum water temperature for the operation of Robo-Kleen is 65° F to 85° F (18° C to 29° C). Do not operate Robo-Kleen when water temperature exceeds 90° F (32° C). Cleaning Pattern Robo-Kleen features an exclusive Controlled Tandem design, which allows the steering wheels to move together without locking into one position. This feature, combined with interval timing in the software, which randomly changes the direction of Robo- Kleen, further enhances movement around the pool. This eliminates the “back and forth” pattern that can occur when wheels are locked into position with fixed timing runs. Robo-Kleen’s ability to change direction easily and often results in coverage of the entire pool quickly. Another benefit of the Controlled Tandem design is that the cleaner does not continually move in one direction around the pool. For roundpools, factorypreset angleis best. This minimizes coiling of the cord. For oval of tandem wheels. pools, removelimit screw for greater angle Automatic Shutdown and Removal Robo-Kleen will automatically shut down after a work cycle of approximately 3 hours. Switch off the power supply for at least 30 seconds before restarting. ALWAYS SWITCH OFF THE POWER SUPPLY BEFORE REMOVING ROBO-KLEEN FROM THE POOL. Remove Robo-Kleen from the water by GENTLY AND SLOWLY pulling in the cable. WHEN ROBO-KLEEN REACHES THE SURFACE, LIFT IT OUT BY THE HANDLE - NOT BY THE CABLE. To minimize debris falling back into the pool during removal, when the cleaner reaches the surface, QUICKLY GRASP A HANDLE AND TURN UNIT OVER TO REST UPSIDE-DOWN ON TOP LEDGE. ALLOW WATER TO DRAIN OUT THE TOP. Carefully reel in an...