Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Aqua Products Dateigröße: 1.49 mb Dateiname: raypak_heater.pdf Unterrichtssprache:

. WHAT TO DO IF YOU SMELL GAS . Do not try to light any appliance. . Do not touch any electrical switch; do not use any phone in your building. . Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. . If you cannot reach your gas supplier, call the fire department. . Installation and service must be performed by a qualified installer, service agency orthe gas supplier. . Do not store or use gasoline or other flammable vapors and liquids in the vicinity ofthis or any other appliance. This manual should be maintained in legible condition and kept adjacent to the heater or kept in a safe place for future reference. ® Part No. 240612 TO WHOM IT MAY CONCERN: The new Raypak series RP2100 pool heaters have been designed to eliminate the need for conventional heat sinks (high temperature piping). The initial connection to the heater is made with a 2" PVC union adapter to which PVC may then be connected with appropriate cement. This newly authorized piping arrangement is described in the installation manual provided by Raypak, and has been successfully tested by Raypak to assure its acceptability. Larry J. Ashton, P.E. Vice President of Engineering and Technical Services CONTENTS 4 PART ONE OWNER’S OPERATING INSTRUCTIONS 24 SECTION 4 SERVICING INSTRUCTIONS 4 SECTION 1 START-UP PROCEDURES 4 5 6 7 Before Start-Up Lighting Instructions & Shut-Off Procedure (Manually Lighted Pilot MV) Operating Instruction & Shut-Off Procedures (Automatically Lighted Pilot IID) After Start-Up 7 SECTION 2 CAUTION 7 SECTION 3 MAINTENANCE & CARE PROCEDURE 8 8 9 Pool & Spa Water Chemistry Cold Weather Operation Winterizing the Pool & Spa Heater 9 PART TWO INSTALLATION/SERVICE INSTRUCTIONS 9 SECTION 1 RECEIVING EQUIPMENT 9 SECTION 2 GENERAL SPECIFICATIONS 10 SECTION 3 INSTALLATION INSTRUCTIONS 24 General Location of Controls 24 Control Adjustments/Replacements 25 Electronic Controls 26 Remote Control Installation 27 Pressure Switch Adjustment 27 Flame Roll-Out Safety Switch 27 High Limit Removal 27 Pilot Safety Millivolt and IID 28 Burner Drawer Removal 27 Gas Valve Removal 27 Main Burner and Orifice Removal 27 Pilot Removal and Cleaning 28 Heat Exchanger Removal 29 Tube Cleaning Procedure 29 Desooting Procedure 29 Control Immersion Well replacement 29 Unitherm Governor (U.G.) Replacement 30 Low Nox Addenda 32 SECTION 5 TROUBLE SHOOTING GUIDE 32 Mechanical 33 Electrical MV Units 34 Electrical IID Units 35 Digital Diagnostics 36 SECTION 6 REPLACEMENT PARTS 42 Warranty 12 Indoor Heater 13 Combustion Air 14 Vent Piping 14 Gas Supply Connections 15 Plumbing For Water Connections 18 RP2100 Heat Exchanger Reversal Procedure 20 Electrical Wiring 21 Wiring Diagram-Millivolt 22 Wiring Diagram-Electronic Ignition 23 Wiring Diagram- Low NOx 3 PART ONE - OWNER’S OPERATING INSTRUCTIONS FOR YOUR SAFETY - READ BEFORE OPERATING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. SECTION 1 / START-UP PROCEDURES Your Raypak Pool/Spa heater has been designed for years of safe and reliable pool/spa water heating. It is available in millivolt or electronic control options. ASME certified units, typical used in commercial applications, are also available. This manual provides operation, installation, maintenance, and service information for these heaters. If your heater has been installed correctly, operating the heater is an easy task. The upper front panel of the heater contains the control center that allows you to turn the heater on or off and adjust the temperature settings for the pool or spa. The temperature range is 65°F (18°C) to 104°F (40°C). The heater with the electronic control option also has a manual switch located on the right cabinet side to allow you to turn the heater off. Section 4 contains more details about the use of the controls in the Controls Adjustments/Replacements sub-section. BEFORE START-UP BURNERS WATER Clean main burners, combustion fan and air louvers Water must be flowing through the heater during of dust, lint and debris. Keep heater area clear and free operation. Insure that system is filled with water and have from combustibles, flammable liquids and chemicals. Do pump operating. not obstruct the flow of combustion and ventilating air. RP2100 DIGITAL IID CAPRON RP2100 DIGITAL IID ASME 4 CAUTION: Propane gas is heavier than air and will settle on the ground. Since propane can accumulate in confined areas, extra care should be exercised when lighting propane heaters. LIGHTING INSTRUCTIONS AND SHUT-OFF PROCEDURES MANUALLY LIGHTED PILOTS MILLIVOLT SYSTEM A. This appliance has a pilot that must be lighted by hand. When lighting the pilot, follow these instructions exactly. B. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor. WHAT TO DO IF YOU SMELL GAS: *Do not try to light any a...

Herunterladen

Geben Sie zwei Ziffern: