Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
4. Pull the long gear shaft straight up (Figure 23a) by the blocks on the ends of the shaft. Hold the seals in the oscillator and the blocks on the shaft. The cam may interfere with the shaft mounting post; if so, turn it slightly on the shaft until it clears the post. The shaft assembly can now be disassembled (Figure 23b). 5. Slide the long gear shaft out of the oscillator (with gears, complete); make sure that you don’t lose the seals out of the oscillator which may fall out at this point (Figure 23b). 5A. Oscillator seals are replaceable. 5B. Ratchet gear set and long shaft are replaceable as a unit. 6. Remove the set screw, short gear shaft, and gears (Figure 24); be sure to keep the gears on. 7. With a small screwdriver (such as a jeweler’s screwdriver), a pencil, or a pen point, depress and remove the coil spring from the lift brush mounting post (Figure 25). Replace the brush and the spring if necessary. 8. The metal ratchet tab slides out of its slot sideways; replace it by removing the center brushes and sliding in a new ratchet tab until it is flush with the edge of plastic holder (Figures 26 and 27). Replace the center brushes. 9. The brush ring pops out of the cleaner body for easy replacement. 10. If you need to replace the bumper, turn the shroud and bumper assembly upside down and remove the two screws holding the bumper to the shroud. Locked Twist CCW 1/4 Turn Pull Straight Up "Click" at this point Swivel assembly 3337 1098 1889 0795 Clip Ocillator Chamber Cap Block Long Gear Shaft Block Cam 1887 0795 1. Slide metal ratchet tab toward end of cleaner body 1885 0795 2. Slide metal ratchet tab down through cleaner body 1884 0795 Figure 23a Figure 22 Figure 23b Figure 24 Figure 25 Figure 26 Figure 27 1886 0795 17 Great White Installation and User’s Guide Reassembly 1. Put both white seals in the oscillator; hold them in place. 2. Install the oscillator on the long gear shaft. Install the ratchet gear on the shaft so that the teeth engage the ratchet on the oscillator. Install the spring, ratchet drum, pinion gear (large gear first), and cam (gear end first) on the shaft (See Figure 28). Hold the gears on the shaft while installing them, and compress the clutch spring to allow assembly to slip into place between the posts (See Figure 28). 3. Install the long gear shaft and end blocks in the cleaning head with the large arm of the cam down (see Figure 29). 4. Reinstall the short gear shaft, set screw and two gears (See Figure 30); the small pinion gears and the shaft set screw go on the side toward the end of the cleaner – away from the oscillator box. Make sure that the gears engage the gears on the long gear shaft. 5. Install the oscillator chamber cap and clip it in place. 6. Install the rubber vacuum skirt on the cleaner with the word ‘OUTSIDE’ showing. Start at the large pin on the back of the cleaner head (see Figure 31) and work around the cleaner. Make sure the skirt is flush against the stop strips on the cleaner head (see Figure 32). 7. Turn the cleaner over. If you removed the bumper and brush ring, replace them now. 8. Install the lower body assembly in the shroud. Fasten the cleaning head in place with 4 screws (2 long, 2 short – see Figure 33). NOTE: Make sure that you do not dislodge the rubber vac skirt while inserting the lower body assembly past the brush ring. This Not This Figure 32 1892 0795 Figure 31 Figure 30 1890 0795 1894 0795 Seals 1895 0795 Swing Cam Arm up for Clearance Make sure Oscillator is partially inserted in chamber while reinstalling Shaft Assembly Oscillator Chamber Figure 28 Figure 29 #10-16x1" Screws #10-16x1-3/4" Screws Center Brush Location Lift Brush Location Center Brush Location Bottom View of Cleaner 1891 0795 Start here with large button when installing vacuum skirt. OUTSIDE 'Outside' will show (facing out) when skirt is correctly installed. Rubber vacuum skirt 1893 0795 Figure 33 18 Great White Installation and User’s Guide Key No. Description Part No. 1 Swivel Assembly GW9012 2 Bumper GW9502 2A Bumper Insert Kit (Set of 4) GW9520 3 Screw Kit (4 short, 2 long) GW9504 4 Shroud GW9501 5 Brush Ring GW9505 6 Oscillator Chamber Cap GW9506 7 Cam Kit (2 & 3 Leg Cams) GW9507 8 Idler Gear Kit (Incl. 3 Gears) GW9509 9 Block Kit (Incl. 2 Blocks) GW9512 10 Long Gear Shaft (Stainless Steel) GW9513 11 Set Screw #4 Self Tapping## 11A Shaft Kit, Stainless Steel (includes Set Screw) GW9536 12 Lower Body* GW9535 13 Lift Brush GW9517 14 Vacuum Skirt GW9508 15 Lift Brush Spring GW9522 16 Ratchet Tab (Stainless Steel) GW9523 17 Oscillator Seal Kit (Incl. 2 Seals) GW9004 18 Oscillator Assembly Kit (Incl. Key #17) (Ratchet Assembly not sold separately) GW9503 19 Center Brush Kit (Set of 2) GW9013 • Hose Kit, 12 sections, each 4 ft in length 41200-0131 • Vacuum Regulator 41200-0200 • Vacuum Regulator Cap 41200-0211 • Reducer Cone GW9015 • Unidapt Handle GW9019 • Vac Port Fitting GW9530 • Flow gauge 41200-0210 • Not Illustrated * Includes Key Nos. 6, 11A, 13, 15, 16, two idl...