Stimmen - 2, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
(P.10) Headphones are plugged into the [PHONES] jack. RUnplug the headphones. .... Non-PCM The [CD IN (COAX)], [DIGITAL IN 1 (OPT)], [DIGITAL IN 2 (OPT)] or [DIGITAL IN 3 (COAX)] terminal is receiving non-PCM input singnals. (P.14–16) R.EQ ERROR1 Measurement failed because the room being measured is too noisy. RReduce the amount of ambient noise. R.EQ ERROR2 Measurement failed because there is no signal input to the microphone. UNLOCK The component connected to the [CD IN (COAX)], [DIGITAL IN 1 (OPT)], [DIGITAL IN 2 (OPT)] or [DIGITAL IN 3 (COAX)] terminal is not turned on. Alternatively, there is no signal input. (P.14–16) ––– kHz The sampling frequency of the input PCM signals is outside the playable range. 62 R-K1000 Apparent faults or malfunctions may be easily resolved. Before calling for service, check the table below for symptoms that match yours. Amplifi er/Speakers Symptoms Possible Cause/Solution Ref. page There is no sound. Check that the system is connected properly, as described in “Connecting the System”. Increase the volume. Cancel the MUTE setting. If there are headphones plugged into the main unit, unplug them. ........ The Standby indicator is flashing red and there is no sound. One of the speaker cords is short-circuited. Unplug the power cord and then reconnect the speaker cord. There may be an internal problem. Turn off the power to the main unit, unplug the power cord and request repairs. .... There is no sound from the headphones. Check that the headphone plug is inserted correctly. Increase the volume. Cancel the MUTE setting. ...... There is no sound from “CD”, “D-IN 1”, “D-IN 2”, or “D-IN 3”. Check that the system is connected properly, as described in “Connecting the System”. Check whether “PCM” is selected as the digital audio output setting on the connected component. .... There is no sound from one of the speakers. Check that the system is connected properly, as described in “Connecting the System”. Adjust the balance. .... There is a booming sound when I select PHONO as the input source. Insert the audio cord plugs securely into the [PHONO IN] jacks. Connect the signal earth wire to the [M] terminal. .... The clock display is fl ashing. Set the time as described in “Setting the Time”... The timer does not work. Set the time as described in “Setting the Time”. Set a start time and end time for the program timer. .... Scrolls text on the display. Disable the Display Saver. .. Troubleshooting Apparent faults or malfunctions may be easily resolved. Before calling for service, check the table below for symptoms that match yours. Amplifi er/Speakers Symptoms Possible Cause/Solution Ref. page There is no sound. Check that the system is connected properly, as described in “Connecting the System”. Increase the volume. Cancel the MUTE setting. If there are headphones plugged into the main unit, unplug them. ........ The Standby indicator is flashing red and there is no sound. One of the speaker cords is short-circuited. Unplug the power cord and then reconnect the speaker cord. There may be an internal problem. Turn off the power to the main unit, unplug the power cord and request repairs. .... There is no sound from the headphones. Check that the headphone plug is inserted correctly. Increase the volume. Cancel the MUTE setting. ...... There is no sound from “CD”, “D-IN 1”, “D-IN 2”, or “D-IN 3”. Check that the system is connected properly, as described in “Connecting the System”. Check whether “PCM” is selected as the digital audio output setting on the connected component. .... There is no sound from one of the speakers. Check that the system is connected properly, as described in “Connecting the System”. Adjust the balance. .... There is a booming sound when I select PHONO as the input source. Insert the audio cord plugs securely into the [PHONO IN] jacks. Connect the signal earth wire to the [M] terminal. .... The clock display is fl ashing. Set the time as described in “Setting the Time”... The timer does not work. Set the time as described in “Setting the Time”. Set a start time and end time for the program timer. .... Scrolls text on the display. Disable the Display Saver. .. Troubleshooting 10–15 22 22 15 11 — 15 22 22 14–16 10 50 15 15 52 52 54 58 English 63 Troubleshooting Troubleshooting Tuner Symptoms Possible Cause/Solution I can’t get reception from a radio station. There is interference (noise). I have used Auto Memory and pressed the [P.CALL] Connect the antennas. Select the broadcast band (AM or FM). Tune the radio to the frequency of the desired station. Install an outdoor antenna away from the road. Turn off any electrical appliances that may be causing interference. Move the system away from the TV. Run Auto Memory again. Manually preset stations with frequencies that you can key, but I still can’t get receive. radio reception. Components connected to the D.AUDIO terminal Ref. page 10, 11 26 26 — 28 29 Symptoms Possible Cause/Solution Ref. page I can’t use the remot...
Dieses Handbuch ist für folgende Modelle:Receiver und Verstärker - R-K1000 (2.4 mb)