Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Kenwood Dateigröße: 151.08 kb Dateiname: B64-1213-00.pdf Unterrichtssprache:

• Check that no metal objects (coins, tools, etc.) are left inside the unit to avoid short circuits. • If you smell or see smoke, turn the power off immediately and consult your Kenwood dealer. • Do not touch the unit during use because the surface of the unit becomes hot and may cause burns if touched. 2 CAUTION Take the following precautions to keep the unit in proper working order. • Be sure the unit is connected to a 12V DC power supply with a negative ground connection. Accessories • Do not open the • Do not install the exposed to direct sunlight, humidity, water may splash over dust exists. NOTE If you have difficulty in installing this in your vehicle, contact your Kenwood dealer. Cleaning the unit If the surface is dirty, wipe it clean with a silicon cloth or soft dry cloth with the power off. 2 CAUTION Do not use hard cloths or paint thinner, alcohol, or other volatile solvents. These may damage external surfaces or remove indicator characters. Part name External V iew Number of Items Part name External V iew Number of Items Battery cable (Yellow) (6 m) 1 Round terminal (Large) 1 Ground cable (Black) (1 m) 1 Round terminal (Medium) 2 Self-tapping screws (o4 . 16 mm) 4 Round terminal (Small) 1 Terminal cover (Power terminal) 1 Grommets 1 Installation procedure 1. Remove the ignition - terminal of the battery short circuits. 2. Set the unit according 3. Connect the input and output 4. Connect the speaker cables. 5. Connect the power cable, power 6. Install the unit in the car. 7. Connect the negative - terminal of the battery. 2 CAUTION • Be sure to turn the power off before changing • If the fuse blows, check cables for shorts, then • Check that no unconnected cables or connectors Do not remove caps from unconnected cables or connectors to prevent • Connect the speaker cables to appropriate speaker connectors Sharing the negative cable of the speaker or grounding speaker cables cause this unit to fail. • After installation, check that the brake lamps, winkers, and wipers Installation Installation board, etc. (thickness : 15 mm or more) Self-tapping screw (o4 . 16 mm) • Since the power amplifier has no parts which require operation, it can be installed at a position away from the driver’s seat without any hindrances. As generally accepted positions for its installation, places such as inside the trunk, etc. can be considered. • Use the extension cables. (Optional.) Type Length 0.5m 1m 2m 4m 5m 6m RCA cable CA-2SL CA-12SL CA-22SL CA-52SL RCA cable (o7mm) CA-3WL CA-13WL CA-23WL CA-53WL RCA cable (o12mm) CA-5W CA-15W CA-25W CA-45W CA-65W 2 CAUTION • Do not install the unit under the carpet. Otherwise heat build-up occurs and the unit may be damaged. • Install this unit in a location which allows heat to easily dissipate. Once installed, do not place any object on top of the unit. • After installing the unit, check to make sure that electrical equipment such as the brake lamps, turn signal lamps and windshield wipers operate normally. • Install the unit securely in a location that does not interfere with driving. Controls Operations of the following control and switches are required in accordance with the center unit and speakers connected with this unit. LPF FILTER OFF MONO(Lch) STEREO OPERATION GND INPUT SENSITIVITY(V) MAXMIN 0.30.5 1.0 L R LINE IN LEFT RIGHT SPEAKER LEVEL INPUT KAC-726 1 2 43 5 6 KAC-526X POWER IN POWER AMPLIFIER FUSE(20A x 2) BATT P.CON(REMOTE) GND LEFT BRIDGED RIGHT SPEAKER OUTPUT KAC-726 7 890 ! FUSE(15A) POWER IN BATT P.CON(REMOTE) GND LEFT BRIDGED RIGHT SPEAKER OUTPUT POWER AMPLIFIER KAC-526X 7 890 ! 1 RCA cable ground lead terminal 2 FILTER switch These switches allow filtering of the speaker output signals. • LPF (Low Pass Filter) position Only frequencies of 80 Hz or lower are output. (Frequencies above 80 Hz are cut.) The Lch and Rch will be mixed before output even if the operation switch is set to STEREO. • OFF position The original sound without filtering is output. 3 OPERATION switch This switch allows selection of the amplification method of input signals. • STEREO position The amplifier can be used as a stereo amplifier. • MONO (Lch) position Amplifies the signal input from the left side only. Set to this position and make bridged connections to use as a high-power monaural amplifier. (The input right signal is not output.) 4 INPUT SENSITIVITY control Set this control according to the pre-output level of the center unit connected with this unit, or to the maximum power output of the genuine- 15 accessory car stereo. Use the diagram on the right as a guide. MIN0.30.5 1.02510 MAX 4 (W) NOTE For the pre-output level instruction manual of the 5 LINE IN terminal 6 Speaker level input terminals 7 Fuse (20 A . 2 : KAC-726) (15 A : KAC-526X) 8 Battery terminal 9 Ground terminal 0 Power control (REMOTE) terminal ! SPEAKER OUTPUT terminals Protection function This unit is equipped with a protection function for protecting this unit and your speakers from various accidents or prob...

Herunterladen

Geben Sie zwei Ziffern: