Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
• At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 40W RMS x 2 @ 4 ohms and .1% THD + N* • 60W RMS x 2 @ 2 ohms, 14.4V supply and .1% THD + N* • 120W RMS x 1 @ 4 ohms, 14.4V supply and .1% THD + N* • Total peak power: 240 watts • Frequency response: 10Hz – 100kHz (–3dB)* • Maximum input signal: 6V* • Maximum sensitivity: 200mV* • THD + N: 0.05% • Signal-to-noise ratio: 85dBA (reference 1W into 4 ohms)* • Signal-to-noise ratio: 101dBA (reference rated power into 4 ohms) * CEA-2006A-compliant . Speaker Output Connectors • Connect the speakers to these terminals, observing proper polarity. • Two-channel operation: Connect the left speaker to the L+ and L– terminals and the right speaker to the R+ and R– terminals. • One-channel (bridged) operation: Connect the single speaker to the R+ and L– terminals. • Minimum speaker impedance for 2-channel operation is 2 ohms. Minimum speaker impedance for 1-channel (bridged) operation is 4 ohms. . Fuse • Replace only with the same type and rating. . Power Input Connectors • +12V: Connect to the positive terminal of the vehicle’s battery. 10 AWG wire is recommended. Install an appropriate fuse holder and fuse (15A minimum) within 18 inches of the battery. Make sure the wire is not damaged or pinched during installation. Install protective grommets when routing wires through the firewall or other sheet metal. • GND: Connect to the vehicle’s chassis. Refer to the picture below. Factory BoltRing ConnectorGround WireNote: Remove any paintbelowring connector. Star Washer • REM: Connect to the “Remote Out” lead from the source unit or to a source of switched 12V+ (ACC). . Input Connectors (RCA) • Connect to the RCA outputs from the source unit or signal processor. . Input-Level Control • Used to match the input level of the amplifier to the output level of the source unit. • See . for the adjustment procedure. . Power On LED • Illuminated when the amplifier is on. . Protect LED • Illuminated under any of the following fault conditions: battery over/under voltage, short circuit in speaker wires, amplifier is too hot, amplifier’s output circuit has failed (DC voltage is present in the amplifier’s output). . Crossover-Frequency Control • 12dB/octave crossover, variable from 32Hz to 320Hz. • See . for the adjustment procedure. . Crossover-Filter Selector • LP: Select for subwoofer(s). • FLAT: Select for full-range speakers when no subwoofer will be used in the system. • HP: Select for midrange speakers or full-range speakers when a subwoofer is used in the system. . Bass-Boost Control • Provides 6dB of boost at 50Hz. Set the Bass- Boost control according to your preference, being careful not to apply enough boost to damage the speaker(s). . Setting Input Level ATurn Input-Level control counterclockwise to 6V (minimum). BWith a dynamic music track playing, turn the head unit’s volume control to the 3/4 position. CTurn Input-Level control clockwise until the music is so loud that it no longer sounds clear (distortion is present in the output). DTurn Input-Level control counterclockwise gradually, just until the music sounds clear, once again. EInput level is now adjusted correctly. . Setting the Crossover ACrossover setting for 5" or larger full-range speakers when no subwoofer is included in the system. BCrossover setting for midrange and/or full-range speakers when a subwoofer is included in the system. CCrossover setting for subwoofers. Note: Acceptable frequency ranges are indicated in gray. This product is designed for mobile applications and is not intended for connection to the mains. A valid serial number is required for warranty coverage. Features, specifications and appearance are subject to change without notice. Declaration of Conformity Harman Consumer Group, Inc. 250 Crossways Park Drive, Woodbury, NY 11797 © 2008 Harman International Industries, Incorporated. All rights reserved. JBL is a trademark of Harman International Industries, Incorporated, registered in the United States and/or other countries. Part No. GT5A402OM 3/08 We, Harman Consumer Group, Inc. 2, route de Tours 72500 Chateau du Loir France declare in own responsibility that the product described in this owner’s manual is in compliance with technical standards: EN 55013:2001+A1:2003 EN 55020:2002+A1:2003 Klaus Lebherz Harman Consumer Group, Inc. Chateau du Loir, France 3/08 ...