Stimmen - 3, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
• At the installation sites, locate and make a note of all fuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. • Choose a safe mounting location away from moisture. • Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself. • Mount the amplifier, using the supplied hardware. Specifications • 55W RMS x 4 channels, plus 225W RMS x 1 channel, @ 4 ohms and .1% THD + N* • 75W RMS x 4 channels, plus 360W RMS x 1 channel, @ 2 ohms and .1% THD + N* • THD + N: 0.03% (rated power @ 4 ohms) • Signal-to-noise ratio: 85dB (reference 1W into 4 ohms)* • Signal-to-noise ratio: 104dB (reference rated power into 4 ohms) • Frequency response: 10Hz – 83kHz and 20Hz – 250Hz • Max power: 660 watts * CEA-2006A-compliant Speaker Output Connectors • Connect the speakers to these terminals, observing proper polarity. • Five-channel operation: Connect the front left speaker to the Front L+ and L– terminals and the front right speaker to the Front R+ and R– terminals. Repeat for the rear speakers, using the Rear L+ and L– terminals, and the Rear R+ and R– terminals. Connect the subwoofer to the Sub+ and Sub– terminals. • Four-channel operation: Connect the stereo speakers to the Front terminals, as above. Connect the single speaker into which the amplifier’s rear channels will be bridged to the Rear R+ and Rear L– terminals. Connect the subwoofer to the Sub+ and Sub– terminals • Three-channel (bridged) operation: Connect one speaker to the Front R+ and Front L– terminals. Connect the other speaker to the Rear R+ and Rear L– terminals. Connect the subwoofer to the Sub+ and Sub– terminals. • Minimum speaker impedance for stereo operation is 2 ohms. Minimum speaker impedance for bridged operation is 4 ohms. Minimum subwoofer impedance is 2 ohms. Fuses • Replace only with same type and rating. Power Input Connectors • +12V: Connect to the positive terminal of the vehicle’s battery. 4 AWG wire is recommended. Install an appropriate fuse holder and fuse (80A minimum) within 18 inches of the battery. Make sure the wire is not damaged or pinched during installation. Install protective grommets when routing wires through the firewall or other sheet metal. • GND: Connect to the vehicle’s chassis. Refer to the picture below. • REM: Connect to the “Remote Out” lead from the source unit or to a source of switched 12V+ (ACC). Front Input Connectors (RCA) • Connect to the front RCA outputs from the source unit or signal processor. Front Input-Level Control • Used to match the front input level of the amplifier to the output level of the source unit. • See for the adjustment procedure. Front Crossover-Frequency Control • 12dB/octave crossover, variable from 32Hz to 320Hz. • See for the adjustment procedure. Front Crossover-Filter Selector • LPF: Select for subwoofer(s). • Flat: Select for full-range speakers when no subwoofer will be used in the system. • HPF: Select for midrange speakers or full-range speakers when a subwoofer is used in the system. Power On LED • Illuminated when the amplifier is on. Subwoofer Input Connector (RCA) • Connect to the subwoofer RCA outputs from the source unit, or signal processor. Rear Crossover-Filter Selector • LPF: Select for subwoofer(s). • Flat: Select for full-range speakers when no subwoofer will be used in the system. • HPF: Select for midrange speakers or full-range speakers when a subwoofer is used in the system. Rear Crossover-Frequency Control • 12dB/octave crossover, variable from 32Hz to 320Hz. • See the adjustment procedure in . Rear Input-Level Control • Used to match the rear input of the amplifier to the output of the source unit. • See for adjustment procedures. Rear Input Connectors (RCA) • Connect to rear RCA outputs from the source unit, or signal processor. EXT/INT Switch • If the source unit has a subwoofer output and you have connected it to the SUB input, set this switch to the EXT position. Otherwise, set it in the INT position. Subwoofer Remote Level Control Connector • Connect the Remote Level Control (RLC) here, using the supplied RJ-11 cable. Subwoofer Level Control • Used to match the SUB input of the amplifier to the output of the source unit. • See for adjustment procedures. Protect LED • Illuminated under any of the following fault conditions: batter...
Dieses Handbuch ist für folgende Modelle:Auto Verstärker - GTO5355OM (1.33 mb)