Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
This unit will be damaged if the power source grounding wire is connected to this terminal. 2C A UTION Left output (White) Right output (Red) Left input Right input n Speaker level input connection GND LINE IN 1.0 INPUT SENSITIVITY(V) BASS ENPHASIS POWER IN GND FUSE(25A) FREQUENCY(Hz) L SPEAKER LEVEL INPUT 25 -+ Genuine-accessory car st er eo ACC Battey Left input Right input Left output Right output Lead terminal (Commercially available parts) Speaker level input terminals Car fuse box 2CAUTION • The genuine-accessory car stereo shall have a maximum power output of no more than 25 W. • Do not connect the speaker output leads from a power amplifier (Optional) to the speaker input terminals of this unit, for this may cause malfunction or damage. • Do not connect cables and leads to both RCA cable input jacks and the speaker input terminals simultaneously, for this may cause malfunction or damage. • Connect the power control lead to a power supply which can be turned ON/OFF by the ignition key switch (ACC line). With this connection, shock noise may be generated when the power of the genuine-accessory car stereo is switched ON/OFF. 6 English n Power wire connection GND LINE IN 1.0 INPUT SENSITIVITY(V) BASS ENPHASIS POWER IN GND FUSE(25A) FREQUENCY(Hz) L R SPEAKER LEVEL INPUT 25 Terminal cover Battery Ground cable (Commercially available part) Battery cable (Commercially available part) Power control cable (Commercially available part) Round terminal (Large) Power terminal Protective Fuse Round terminal (Small) Round terminal (Medium) 2WARNING To prevent fire caused by a short in the wiring, connect a fusible link or breaker nearby the battery’s positive terminal. Wiring • If a buzzing noise is heard from the speakers when the engine is running, connect a line noise filter (optional) to each of the battery wire. • Do not allow the cord to directly contact the edge of the iron plate by using Grommets. • Connect the ground wire to a metal part of the car chassis that acts as an electrical ground passing electricity to the battery‘s negative -terminal. Do not turn the power on if the ground wire is not connected. • Be sure to attach a protective fuse into the battery wire close to the battery. Use a protective fuse having a capacity that is about 10 A higher than the maximum current drawn by the amplifier. • Use vehicle-type (fire-resistant) power supply wiring wire for the battery wire and the ground wire. The current capacity of the power supply wiring wire should be about 10 A higher than that of the protective fuse capacity (which means about 20 A higher than the maximum current drawn by the amplifier). • When more than one power amplifier are going to be used, use a power supply wiring wire and protective fuse of greater current-handling capacity than the total maximum current drawn by each amplifier. Power terminal Connect to their respective terminals the power control wire, power supply wire, and ground wire, all of which pass through the associated terminal cover. Once the connections are complete, place the cover on the terminal section. Example:One Power Amplifier Is Used Maximum Current Drawn 15 A Protective Fuse 30 A . 1 [15 A . 2] Cross-sectional Area of Wiring Wire (AWG) 3 mm2 (AWG 12) or greater . 1 30 A 15 A 15 A 15 A 15 A English 7 Troubleshooting Guide What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.Before calling service,first check the following table for possible problems. PROBLEM POSSIBLE CAUSE SOLUTION No sound. • Input (or output) cables are • Connect the input (or output) (No sound from one side.) disconnected. cables. • Protection circuit may be • Check connections by referring activated. to "Protection function". • The fuse may be blown • Replace the fuse with a new because the volume was too fuse and use a lower volume. high. The output level is too The input sensitivity adjusting Adjust the control correctly small (or too large). control is not set to the correct referring to “Controls”. position. The sound quality is bad. (The sound is distorted.) • The speakers cable are connected with wrong + / polarity. • A speaker cable is pinched by a screw in the car body. • The switches may be set improperly. • Connect them properly checking the + / -of the terminals and cables well. • Connect the speaker cable again so that it is not pinched by anything. • Set switches properly by referring to "Controls". Specifications Specifications subject to change without notice. Audio Section Max Power Output (4 .) ..............................................................................240 W . 1 (at 100 Hz) Rated Power Output (4 .)........................................120 W . 1 (DIN45324, +B=14.4V, at 100 Hz) (2 .) ........................................................160 W . 1 (0.8 % THD at 100 Hz) Signal to Noise Ratio............................................................................................................100 d...