Stimmen - 2, Durchschnittliche Bewertung: 3.5 ( )

Hersteller: Jensen Dateigröße: 1.38 mb Dateiname: Unterrichtssprache:

With its deep-bass reproduction and plenty of reserve power, low harmonic distortion and neutral reproduction, the Power series of amplifiers takes Mobile Hi-Fi to new heights. Like all Jensen products, when it comes to accurate sound reproduction the Power series takes a back seat to no one. Jensen will bring your Hi-Fi experience to new heights with the following features: • MOSFET Power Supply • High Current Bi-Polar Output Transistors • Optimized Class B Design Minimizes Distortion and Reduces Idle Current • Easily Drives 2-Ohm Loads • Pass-Thru RCA's • Variable Bass EQ 0 - 12dB @ 45 Hz • 12dB / Octave Low Pass and High Pass filters • Variable Input Level 400mV - 5V • Short Circuit, DC-offset and Thermal Overload Protection Circuitry • Diagnostic LED's - Green: Power, Red: Standby / Fault Power 400 / 760 / 880 / 920 • Low Pass Filter 40 - 300 Hz • High Pass Filter 40 - 300 Hz • High Pass / Low Pass / Full Range Selector Switch • Stereo / Mono Mode Switch (Power 400 and 880 only) • 2/ 3 / 4 Channel Mode Switch (Power 760 and 920 only)) Power 900 / 1050 • Mono Subwoofer Amp • Low Pass Filter 40 - 240 Hz (Power 900) • Low Pass Filter 40 - 150 Hz (Power 1050) • Subsonic Filter 10 - 40 Hz, 12dB / octave (Power 900) • Subsonic Filter 15 - 55 Hz, 12dB / octave (Power 1050) • Remote Input Level Control (Remote Bass Control) w/ 5 Meter Interface Cable Specifications Power 400 / 760 / 880 / 920 • Load Impedance: 2 / 4-Ohm • Signal to Noise @ 1 kHz: >100dB (rated power) • Channel Separation @ 1 kHz: >60dB • Frequency Response: 5-60 kHz, -3dB • Input Impedance: 20 kHz, nominal • THD+N @ 5 Watts: 0.02%, 1 kHz, 14.4VDC Power 900 / 1050 • Signal to Noise @ 120 Hz: >100dB (Rated Power) • Channel Separation Not Applicable • THD+N @ 5 Watts: 0.02%, 125 Hz, 14.4VDC Power Output RMS Power Output @ 2% THD+N, 1kHz, 14.4VDC Power 400 • 75 x 2 Watts, 4-Ohm • 100 x 2 Watts, 2-Ohm • 200 x 1 Watts, 4-Ohm Bridged Power 760 • 75 x 4 Watts, 4-Ohm • 100 x 4 Watts, 2-Ohm • 190 x 2 Watts, 4-Ohm Bridged Stereo Power 880 • 135 x 2 Watts, 4-Ohm • 220 x 2 Watts, 2-Ohm • 440 x 1 Watts, 4-Ohm Bridged Power 900 • 300 x 1 Watts, 4-Ohm • 450 x 1 Watts, 2-Ohm Power 920 • 100 x 4 Watts, 4-Ohm • 140 x 4 Watts, 2-Ohm • 230 x 2 Watts, 4-Ohm Bridged Stereo Power 1050 • 350 x 1 Watts, 4-Ohm • 525 x 1 Watts, 2-Ohm Specifications subject to change without notice. POWER Amplifiers 3 Installation Before you begin the installation of your Power series amp remember, there are two ways to do things – right and twice! Use the proper installation techniques, tools and accessories to ensure that your Jensen Power series amp will put out all the power it was designed to. If necessary, seek a professional installer to have the amplifier installed correctly. Most mobile amp installations do not have the proper gauge wire for power and ground – do not let your amp be a victim of this common installation oversight! NOTE: This device is a high-power audio amplifier intended for installation in vehicles with a 12-Volt negative ground electrical system. Attempting to connect or operate the amplifier with another type of electrical system may cause damage to the amplifier or the electrical system. Installation Assistance For installation assistance, call 1-800-323-4815 during normal business hours, or visit at any time. Supplies and Tools Needed To install the amplifier, you will need tools, supplies and adapters. It is best to make sure you have everything you need before you start. Supplies • Black electrical tape • Amplifier Installation Kit Tools • Cordless drill with assortment of bits • Flat-head and Philips screwdrivers • Wire cutters/strippers • Crimping tool • 12-volt test light or digital multimeter • Wire brush, sandpaper or scraping tool (ground connection to vehicle should be a clean, unpainted metal surface) Disconnect Battery Disconnect the negative (-) battery cable before starting the installation. Check the battery ground (there should be two (2) ground wires coming from the battery – one going to the starter mounting bolt or engine block and another going to the vehicle chassis) and make sure the battery is grounded to the chassis with at least a #8 gauge wire. Also check the alternator connections, making sure they are tight and free from corrosion, rust or dirt. Location and Mounting The amplifier’s compact design allows ...

Herunterladen

Geben Sie zwei Ziffern: