Stimmen - 2, Durchschnittliche Bewertung: 4.5 ( )

Hersteller: Earthquake Sound Dateigröße: 1.05 mb Dateiname: Unterrichtssprache:

Set your audio system to a comfortable loudness level. Earthquake Sound Corporation does not assume liability for damages resulting from the direct use of Earthquake amplifiers or other Earthquake products and urges users to play their music at moderate listening levels. 3 2 1 -1 1/2 1 1/2 1/4 or less 8 6 4 97 100 102 105 110 115 90 92 95 THE CHART (ON THE SIDE) SHOWS THE U.S. GOVERNMENTS OCCUPATIONAL SAFETY AND H E A LT H A D M I N I S T R AT I O N ( O S H A ) REGULATIONS WHICH WERE IN EFFECT AT THE TIME OF THIS PUBLICATION FOR PERMISSIBLE NOISE EXPOSURE, PER 29CFR1910.95, TABLE G-16. SOUND LEVEL DBA DURATION IN HOURS CAUTION: DO NOT connect the remote wire to the head unit as this will damage your sound system. RESET In case the system goes into protection, simply turn off the audio source, lower the volume and slide the switch to RESET then back to AUTO ON position. REMOTE ON When the switch is on REMOTE ON, the amplifier relies on the remote wire to detect the signal and turn the amplifier on or off. NOTE: RCA outputs must be inserted in CH1/2 for the amplifier to detect any incoming signal. 23 Specifications Are Subject To Change Without Notice 4 5 SPECIFICATIONS Model T500W/2 T1000W/2 T2000W/4 T2000WD/1 TD5X Class A/B A/B A/B D D Number of Channels 2 2 4 1 Mono 4 Full Range + 1 Mono Max Power Output 800 Watts 1400 Watts 2000 Watts 2000 Watts 3000 Watts Max Power 4-Ohm Bridged 1 x 400 1 x 700 2 x 250 1 x 1000 @ 2W 2 x 100 @ 4W + 1 x 300 @ 4W Max Power 4-Ohm Stereo 2 x 150 2 x 300 4 x 100 1 x 600 @ 4W 4 x 100 @ 4W^ + 1 x 600 @ 2W THD @ 4-Ohm THD @ 2-Ohm > 0.01% > 0.05% > 0.01% > 0.05% > 0.01% > 0.05% > 0.01% > 0.016% > 0.01% > 0.016% Channel Separation > 60 dB > 60 dB Crossover Frequency, LPF Crossover Frequency, HPF Crossover Frequency, SUB 50 - 250 Hz 50 - 250 Hz N/A 50 - 250 Hz 50 - 250 Hz N/A 50 - 250 Hz 50 - 250 Hz N/A N/A N/A 50 - 300 Hz 40 - 400 Hz 40 - 400 Hz 40 - 160 Hz Bass Boost 0 - 18 dB 0 - 18 dB 0 - 18 dB 0 - 10 dB N/A Fuse 1 x 30 Amp 2 x 25 Amp 2 x 20 Amp 2 x 30 Amp 3 x 25 Amp Signal-to-Noise Ratio 95 dB Below Rated Power 95 dB Below Rated Power Dimensions (H x W x D) 2-1/4” x 9-3/4” x 9” 2-1/4” x 9-3/4” x 13-5/16” 2-1/4” x 9-3/4” x 13-3/8” 2-1/4” x 9-3/4” x 11” 2-1/4” x 9-3/4” x 16-3/8” Net Weight 4.25 lbs 6.4 lbs 6.5 lbs 6 lbs 9 lbs * Dimensions include plugs, terminals and mounting feet. ^ Minimum impedance is 4W. Specifications Are Subject To Change Without Notice Please refer to the warranty guidelines provided with the amplifier. It is recommended that you keep a copy of your sales receipt and note your serial number here for future reference. SERIAL NUMBER 6 7 T500W/2 Set Xover switch to FULL K-10, ten-inch bass tube, in mono application (4 Ohms minimum) 7.0V 17.0V 4.0V 10.0V 2.5V 5.0V 1V 1V The gain knob is not a volume control. It is designed to match the input level of the amp to the output level of the source unit. Over driving "clipping" the input stage of the amp will cause damage to the amplifier (please refer to table for setting). MAX INPUT VOLTAGE BEFORE CLIPPING RCA LEVEL SPEAKER LEVEL 50Hz 90Hz 125Hz 170Hz 210Hz 250Hz XOVER KNOB SETTING T500W/2 One 30A fuse To car chassis / ground To remote turn on / trigger To battery positive (+) Bridgeable Speaker outputs, minimum 4-Ohms mono. MODE SELECTOR: This feature tells the amplifier to run in either HIGH PASS, FULL RANGE or LOW PASS MODE LEVELADJUST: Allows the amplifier to deliver a controlled maximum sound level into selected channel(s) when the volume is turned to max. This acts as a volume limiter for the system, preventing you from over driving the speakers or subwoofers. LOW LEVELINPUTS: Low level inputs ra...

Herunterladen

Geben Sie zwei Ziffern: