Stimmen - 3, Durchschnittliche Bewertung: 3 ( )

Hersteller: PYLE Audio Dateigröße: 428.7 kb Dateiname: Unterrichtssprache:

If the mounting surface is carpeted, measure the hole centers and mark with a felt tip pen. Before attempting to drill the mounting holes, take note of any wires, lines or other devices in your vehicle which may be located behind the mounting surface! Then drill pilot holes in the mounting surface for the mounting screws and insert them. Tighten the screws securely. wiring tips When making electrical connections to your amplifier, please observe the following: Use at least 8 gauge wire for power and ground connections. Wire the amplifier directly to the car battery. For the ground connection, use the shortest possible wire to a good chassis ground point. Wire the Remote connection to the auto start lead of your head unit, equalizer or power antenna. fuses About power fuses: Pyle Chopper Series amplifiers feature built-in fuse systems. These fuses protect both the amplifier and the electrical system in your vehicle from fault conditions. If you ever need to replace the fuse in your Pyle Chopper Series amp, use a fuse of exactly the same type and rating. A different type or rating of fuse may result in damage or fire. No output. troubleshooting No output. troubleshooting protection circuitry The built-in protection circuitry in the Pyle Chopper Series amplifiers will disable the amplifier if it senses an input overload, a speaker short circuit, or extreme temperature conditions. When the protection circuit is activated by any of these conditions, the Protection LED will be illuminated. If this occurs, carefully inspect the system to determine the source of the problem. • If the shutdown was a result of a thermal overload condition, allow the amplifier to cool down before attempting to restart it. • If the shutdown was a result of an input overload, or speaker short circuit, be sure to correct the condition before restarting. The amplifier can be restarted by turning the remote power OFF and then ON again. Confirm that all terminal strip connections are secure and tight. Check both in-line and built-in fuses. Both the +12V and the Remote terminals must have +12v referenced to chassis ground. Confirm that the audio signal source (car radio, equalizer, etc.) is connected and is supplying output signal. To check if the amp is supplying signal, unplug the cables from the signal source (but leave them plugged into the amp). Briefly tap the center pin of each of the disconnected RCA plugs with your finger. This should produce a noise (feedback) in your speakers. Only one channel works. Confirm that all terminal strip connections are secure and tight. Check the Balance control on the head unit (or other source) to verify that it is set to its midpoint. If you are using the Low Level RCA input, reverse the input plugs at the amplifier (i.e., switch the L with the R). If the channels which is silent switches to the other side, the problem is either in the head unit/other source or the connecting cables. Weak output. Readjust the Input Level Control(s) to better suit the input signal. Noise in the audio. If the noise is a “whine” whose pitch follows the engine speed, confirm that the amplifier and any other signal sources (head unit, etc.) are properly grounded. If the noise is a “clicking” or “popping” noise whose rate follows the engine speed, this usually means that the vehicle is equipped with resistor spark plugs and wires, or that the ignition is in need of service. Check the rounting of the speaker and input wires to make sure they are not adjacent to wires which interconnect lights and other accessories. If the above steps fail to improve or clear noise interference, the system should be checked by a professional mobile audio installer. 23 STOP YES! NO! 2-c hannel Amplifier (Operating in Stereo) 4 ohm 4 ohm Two 4-ohm speakers, wired in stereo, will present a 4-ohm load to each channel of the amplifier. Most two- channel amplifiers will work well in this configuration. Two 4-ohm speakers, wired in parallel to a bridged two-channel amplifier. will present a 2-ohm mono load to the amplifier. MOST TWO-CHANNEL AMPLIFIERS DO NOT SUPPORT 2-OHM MONO OPERATION! AMPLIFIER DAMAGE COULD RESULT! 4 ohm 4 ohm 2-channel Amplifier (Operating in Bridged Mono) notes precautions Do not operate the amplifier when it is unmounted. Attach all audio system components securely within the automobile to prevent damage, especially in an accident. Do not mount this amplifier so that the wire connections are unprotected, or in a pinched condition, or likely to be damaged by nearby objects. 23 STOP YES! NO! 2-c hannel Amplifier (Operating in Stereo) 4 ohm 4 ohm Two 4-ohm speakers, wired in stereo, will present a 4-ohm load to each channel of the amplifier. Most two- channel amplifiers will work well in this configuration. Two 4-ohm speakers, wired in parallel to a bridged two-channel amplifier. will present a 2-ohm mono load to the amplifier. MOST TWO-CHANNEL AMPLIFIERS DO NOT SUPPORT 2-OHM MONO OPERATION! AMPLIFIER DAMAGE COULD RESULT! 4 ohm...

Herunterladen

Geben Sie zwei Ziffern: