Stimmen - 4, Durchschnittliche Bewertung: 4.3 ( )

Hersteller: Dual Dateigröße: 1.21 mb Dateiname: xpe.pdf Unterrichtssprache:

TYPICAL MOUNTING METHOD XPE SERIES INSTALLATION Connection Descriptions NOTE Be sure to follow specific instructions included with your amplifier installation kit (not included with this amplifier). The information below should be used a general guideline only. Power Wire (+12V) • Disconnect negative battery terminal before proceeding. Consult a qualified technician for instructions if you are unsure. • Plan wire routing before cutting any wires to length. Begin by routing the power +12V wire from the battery to the amplifier location. Use a grommet when running wires through the firewall or metal openings. Avoid running the power wire near existing vehicle wiring to prevent induced noise from entering the audio system. • Use extreme caution when drilling holes to avoid damaging fuel lines or existing vehicle wiring. • The +12V wire MUST be fused within 18" of the battery for protection of the vehicle’s electrical system. Ground Wire (GND) • The amplifier ground wire should be as short as possible. Choose a clean unpainted section of metal or the vehicle chassis when attaching the ground connection. Be sure to clean the area of any dirt or grease. Remote Turn-on Wire (REM) • The remote turn-on wire connects to the head unit's amplifier turn-on lead or power antenna output. Speaker Wires • Choose adequate gauge speaker wire depending on your exact amplifier/speaker combination. Be sure to observe polarity when connecting. • Do not ground any speaker wires or connect any speaker wires together. Input Signal • The amplifier's input signal connects to the head unit's low level (RCA) or high level (speaker wire) outputs. • Low level input signal deliver the best performance. If unavailable, use the high level inputs -when interfacing with factory head unit for instance. CAUTION • Do not use both low and high level inputs at the same time -connect only one or the other. • Never run any wires underneath or outside the vehicle. XPE SERIES INSTALLATION Audio Inputs and Controls XPE1700LINEINPUTSLEFTRIGHTGAINMINMAXLPOFFFREQUENCY50Hz500HzX-OVERBASSBOOST0FF6dB12dBPHASE0180SUBSONIC0FFON3456721 SPEAKERINPUTSLINEINPUTSLEFTRIGHTGAINFREQUENCYLPOFFHP50Hz500HzBASSBOOST0FF6dB12dBX-OVERMINMAXXPE2700842165 LINEINPUTSRIGHTLEFTFRONTREARRIGHTLEFTBASSBOOST0FF6dB12dB0FF6dB12dBFREQUENCY50Hz500Hz50Hz500HzLPOFFHPLPOFFHPGAINMINMAXMINMAXSPEAKERINPUTSINPUTMODE4CH2CHX-OVERFRONTREARXPE47001982564 12345 RCA Line Inputs Bass Boost Gain Phase Sub-Sonic Speaker Inputs Crossover Frequency Control Input Mode Crossover Mode 6789 XPE SERIES INSTALLATION Power and Speaker Connections 30AFUSES30AXPE1700SPEAKER+-GNDREMBAT+ POWER13254 25AFUSEXPE2700GNDREMBAT+ POWERSPEAKERSLEFT+-RIGHT+- BRIDGE13254 25AFUSES25ALEFT+-RIGHT+- SPEAKERSBRIDGEFRONTREARGNDREMBAT+ POWERXPE470013254 123 Ground Connection Fuse(s) Remote Connection Speaker Connection(s) +12VDC Battery Connection 45 XPE SERIES INSTALLATION Typical Wire Routing REM (TURN-ON LEAD) Main Power Connections Connect +12V, GND and REM wires accordingly. A suitable fuse MUST be installed on the +12V lead within 18" of the battery for protection of the vehicle’s electrical system. Fuse Rating When replacing fuses, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage the amplifier. XPE1700 30 amp ATO x 2 XPE1700 4 awg XPE2700 30 amp ATO x 1 XPE2700 10 awg XPE4700 25 amp ATO x 2 XPE4700 8 awg Power/Ground Wire Size For optimum performance, use only the wire size listed below or larger. Make sure to use the same size power and ground wire. XPE SERIES INSTALLATION Amplifier Connections Speaker Connections 2 Speakers (stereo) Subwoofer (mono) Connect speaker wires observing polarity. The minimum impedance load for the XPE2700 and XPE4700 is 2 ohms stereo and 4 ohms bridged. Use of loads lower than these is not recommended and may cause amplifier damage. The XPE2700 and XPE4700 can be wired for stereo, bridged or stereo/bridged simultaneous operation. Typical Stereo Wiring (2 ohms minimum) Typical Bridged Wiring (4 ohms minimum) XPE2700 speaker connections shown Input Signal Connections Low Level Input (RCA) Low level (RCA) input signal is preferred for best performance. Typical trunk-mount amplifier installations require a 17-20 foot RCA cable. Most trucks and under-seat applications require a 6-9 foot RCA cable. Using twisted pair construction RCA cables will minimize noise. High Level Input (Speaker Wire) High level inputs should only be used when RCA outputs are not available from the head unit. Connect the head unit speaker outputs to the high level input connector as shown below. The black wire (signal reference ground) may or may not require a connection to chassis ground -depending on your particular installation. CAUTION Do not use both low and high level inputs at the same time -connect only one or the other. XPE SERIES OPERATION Conf...

Herunterladen

Geben Sie zwei Ziffern: