Stimmen - 3, Durchschnittliche Bewertung: 3.7 ( )

Hersteller: Lanzar Car Audio Dateigröße: 1.23 mb Dateiname: VCT2310.pdf Unterrichtssprache:

Ground (10.5-16V) 270x44.5x228 10.63x1.75x9 270x44.5x305 10.63x1.75x12 VECTOR Owner's Manual features and controls 2 ch amp VCT-2IIQ • VCT-22IO VECTOR Owner's Manual - features and specifications 2 ch amp VCT-23IO • VCT-24IO • VCT-25IO crossover mode selector Input level controls crossover frequency control bass boost level control sub sonic control low level input high level input AUX line outputs power LED protection LED power fuse power terminals speaker connectors When used with normal, full range system, set this switch to "FULL". If you wish to use the internal crossover to power a driver or specific frequency range, use the 'LPFor "HPF" FOR the"LOWPASS' OR HIGHPASS’settings. Enables the matching of input levels to the output levels from head unit (or other signal source). The input sensitivity of adjustment ranges from 6Vto200mV. When crossover mode selector is in HIGHPASS mode, this control sets the lower frequency limit for audio program sent to the speakers. When crossover mode selector is in LOWPASS mode, this control sets the upper frequency limit for audio program sent to the speakers. The crossover is continuously variable adjustment from 40 to 250 Hz. This control permits adjustment of the bass level up to an increase of approximately up to 1SdB. (VCT-2310/2410/2510) When the sub sonic selector switch is in 'ON" mode, this filter control permits continuously variable adjustment from 10 to 100Hz. (VCT-2310/2410/2510) This amp features RCA type jacks for high impedance Input. Use these with car stereo output which uses RCA type connector cables. If your car stereo jacks are not RCA type output, use the high-low level input adaptor to connect the speaker output leads of car stereo and the RCA input jacks of amp. This amp features RCA jacks for AUX line outputs. Use these for unlimited system expansion to the next VECTOR. This indicator is illuminated in GREEN when power is applied. This indicator is Illuminated in RED when the built-in protection circuitry is actirated. The fuse protects the amplifier and your car's electrical system from short circuit conditions. Use these connectors to deliver power, ground, and remote turn-on control to the amplifier. These terminals are to guarantee high conductivity and minimum signal loss. output power @ 144» DC, 1 KHz RMS Rower @4 Ohm Htt@40hm RMS Porn @2 Ohm TUB @2 Ohm Maxima Power Output Bridged Pom it 4 Output frequency response input impedance low level inputs input sensitivity low level inputs S/M ration channel separation crossover filters low Pass highPass bass boost sub sonic litter VCT-2310 150 Watts x 2 250Wattsx2 250 Wattsx2 3WWattsx2 1500 Watts x 2 3000 Watts x1 stereomode bridged mode maximum current draw power supply voltage dimensions (WxHx LI mm Inches VCT-2410 200 Watts x 2 300 Wattsx2 300Wattsx2 4№>Wattsx2 2000 Watts x 2 4000 Watts x1 15 Hz-30 KHz VCT-2510 300 Wattsx2 450 Wattsx2 450 650 Wattsx2 2500Wattsx2 5000 Watts x1 — 10K Ohms — — 200mV~6VAdjustable - — >95dB — — >6500 — 40 Hz-250 Hz 40 Hz-25...

Herunterladen

Geben Sie zwei Ziffern: