Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
to the desired frequency or position. 13. Once the system is powered up, set the volume control on the head unit to about the 2 o'clock position, and then set all the amplifiers' level controls for maximum output level. 14. Further fine tuning of the various controls may be necessary to obtain the desired results. jdanzar Vibe Owner’s Manual - 5 Features and Controls VIBE700.1D / 1000.1 D / 1800D / 3100D / 4KD Level Sub Low Phase Bass sonic Pass shift Boost Cx) fx) Gc) VI 00 X) PWR PROT. f \ f \ | | ( — \ Min Max 16 40 60 ÄJ60 0* 180° 0 +1ÖJ / \ i i i i I I I I 0 0 0 0 0 0 0 6 - Jßanzar Vibe Owner’s Manual _ Features and Controls 1. Line Out RCA Jacks- The LINE OUT allows you to build multiple amplifier systems with out having to use splitter cords to distribute thesignal. Now it is simple it matter of bringing one set of RCAsinto the first amplifier, then using the line out RCA jacks as the feed to the next amplifier. 2. Line Input RCA Jacks- These inputsare forsignal cablesfrom thesource. Always usehigh quality shielded RCA cables. 3. Input Level Control- Enables the matching of input levels to the output levels from the head unit(or other signal source). 4.Variable Subsonic Filter- 15Hz~40Hz 5.Low Pass Filter- When Crossover Mode Selector is in Low Pass Mode, this control limits the frequencies which will be distributed to the speakers to thosebelow thevalue to which this is set within the range50~150Hz. 6.Phase Shift- Allows you to change the phase of your subwoofer from 0 to 180 degrees to help compensate for timing differences between drivers. 7.Bridged Mode 8.Bass Boost Control- 0~ + 18dB 9.Power & Protection Indicators- Provide instant information on status ofamplifier, including short-circuit and thermal overload alerts. 10.Speaker Terminals- These chrome, plated connectors can accept from 26 to 8 gauge wire. Be careful to observeproper polarity when connecting the cables. X anzar Vibe Owner’s Manual - 7 System Wiring ■ SIGNAL INPUT AND BYPASS OUTPUT CONNECTION VIBE700.1D / 1000.1 D / 1800D / 3100D / 4KD ■ SPEAKER OUTPUT CONNECTION VIBE700.1D / 1000.1 D J 1Q0QD / 31000 f 4KD 8 - jCanzar Vibe Owner’s Manual ■ POWER INPUT CONNECTION System Wiring TO REMOTE GAIN CONTROLLER CHASSIS GROUND (BARE METAL) TO CAR STEREO AUTO ANTENNA Fuse Rating MODEL FUSES VIBE7Q0.1D 20A x 2 VIBE1000.1D 30A x 2 VIBE1800D 30A x 4 VIBE3100D 30A x 5 VIBE4KD 30A x 5 anzar Vibe Owner's Manual System Wiring ■ BRIDGING TWO AMPLIFIER VIBE700.1D / 1000.1 D / 1800D / 3100D / 4KD Master Amp ■X_/—V. ,®,&& W & oo L- >pj ® Slave Amp & ,®, & ,® lln Max 18 40 80 -IHO 0 100* 0 * 1W 3 Vj (BRIDGED SWITCH : SLAVE POSITION) Bridged mode w Bridging two amplifiers can be done only between two amplifiers of the same model number. SPEAKER IMPEDANCE 2 Ohms! 10 - jCanzar Vibe Owner's Manual Troubleshooting_ Before removing your amplifier, refer to the list below and follow the suggested procedures. Always test...
Dieses Handbuch ist für folgende Modelle:Auto Verstärker - 1800D (265.12 kb)
Auto Verstärker - 3100D (265.12 kb)
Auto Verstärker - 4KD (265.12 kb)
Auto Verstärker - 700.1D (265.12 kb)