Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
These new standards give all participating manufacturers (and many don't participate) a baseline when comparing amplifiers of similar power output. The CEA Power rating protects you, the customer. « Power is power - it doesn't matter who makes it,” is not always true. What does matter is whether the power can be produced in the first place. The RMS rating is the true power you are getting. At Jensen, to be fair to you and to the competition, we rate our amps in the two most popular ratings, including the CEA RMS rating. So feel confident that your Jensen purchase decision was a sound one, and remember "If it's Too Loud, You're Too Old." Before You Begin We need to get the legal stuff out of the way, so please keep reading. Afterwards, you’ll be armed with the knowledge to install your new hard-hitting, speaker-pumping Jensen amplifier. Exposure to loud sounds or music can permanently damage your hearing. Unfortunately, in many cases, the damage is not noticeable until years later. In addition, loud music may hinder your ability to hear traffic, police, and fire or emergency vehicles. Please be responsible and have respect for other people by listening at moderate volumes! Warranty Service If your Jensen amplifier should ever require service, you will need the original dated receipt. If you must return the unit for any reason, always include the receipt with the product. POWER 5500 5-Channel Amplifier i POWER 5500 5-Channel Amplifier Features and Specifications Your new Jensen Power mobile stereo power amplifier is the amplifier of choice for the high demands of auto sound reproduction. With its deep-bass reproduction and plenty of reserve power, low harmonic distortion and neutral reproduction, the Power series of amplifiers takes Mobile Hi-Fi to new heights. Like all Jensen products, when it comes to accurate sound reproduction the Power series takes a back seat to no one. Jensen will bring your Hi-Fi experience to new heights with the following features: • MOSFET Power Supply • High Current Bi-Polar Output Transistors • Optimized Class B Design Minimizes Distortion and Reduces Idle Current. • Easily Drives 2-Ohm Loads • Fullrange Highpass Filter: Continuously Variable 16Hz ~160Hz • Subwoofer Infra-Sonic Filter: Continuously Variable 16Hz ~60Hz • Subwoofer Low Pass Filter: Continuously Variable 30Hz~160Hz • Subwoofer Bass EQ Filter: Continuously Variable 0~12dB @ 45Hz • Short Circuit, DC-Offset and Thermal Overload Protection Circuitry • Diagnostic LED's: Green - Power, Red - Standby / Fault • Remote Input Level Control (For subwoofer channel) w/ 5 Meter Cable Specifications • Load Impedance - 2/4 Ohm • Frequency Response - 10~60kHz (Subwoofer - 16~160Hz), -3dB • THD+N @ 1kHz, 5 Watts - 0.02%, 4-Ohm, 14.4VDC • Stereo Separation @ 1 kHz - >60dB • Signal to Noise Ratio - >100dB (Rated Power) • Input Sensitivity - 400mV~5V • Input Impedance - 20k0hm nominal • Fuse -1 x 70 Amp MAXI Fuse • Size - L22" x H2.5" x W9" • Weight-10.8lbs Power Output ^vssss % CCEA «Î/l-20^ RMS Power Output @ 2% THD+N, 1kHz, 14.4VDC 4 Channels 4 x 70 Watts 4-Ohm 4 x 90 Watts 2-Ohm Bridged Stereo 2 x 180 Watts 4-Ohm Mono - Subwoofer 1 x200 Watts 4-Ohm 1 x 300 Watts 2-Ohm Specifications subject to change without notice. Installation Before you begin the installation of your Power 5500 amp remember, there are two ways to do things - right and twice! Use the proper installation techniques, tools and accessories to ensure that your Jensen Power series amp will put out all the power it was designed to. If necessary, seek a professional installer to have the amplifier installed correctly. Most mobile amp installations do not have the proper gauge wire for power and ground - do not let your amp be a victim of this common installation oversight! NOTE: This device is a high-power audio amplifier intended for installation in vehicles with a 12-Volt negative ground electrical system. Attempting to connect or operate the amplifier with another type of electrical system may cause damage to the amplifier or the electrical system. Installation Assistance For installation assistance, call 1-800-323-4815 during normal business hours, or visit at any time. Supplies and Tools Needed To install the amplifier, you will need tools, supplies and adapters. It is best to make sure you have everything you need before you start. Supplies • Black electrical tape • Amplifier Installation Kit Tools • Cordless drill with assortment of bits • Flat-head and Phillips screwdrivers • Wire cutters/strippers • Crimping tool • 12-volt test light or digital multimeter • Wre brush, sandpaper or scraping tool (ground connection to vehicle should be a clean, unpainted metal surface) POWER 5500 5-Channel Amplifier Disconnect Battery Disconnect the negative (-) battery cable before starting the installation. Check the battery ground (there should be two (2) ground wires coming from the battery - one go...