Stimmen - 4, Durchschnittliche Bewertung: 4.5
(
)
)
|
Anleitung Zusammenfassung
Features · Requires very few external components · Thermally protected · High output power · Reverse polarity safe · Fixed gain · Capability to handle high energy on outputs (VP = 0 V) · Good ripple rejection · No switch-on/switch-off plop · Mute/stand-by switch · Protected against electrostatic discharge · Load dump protection · Compatible with TDA1517 (except gain). · AC and DC short-circuit-safe to ground and VP QUICK REFERENCE DATA PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT Supply voltage range operating VP 6,0 14,4 18,0 V non-operating VP - - 30 V load dump protected VP - - 45 V Repetitive peak output current IORM - - 2,5 A Total quiescent current Itot - 40 80 mA Stand-by current Isb - 0,1 100 mA Switch-on current Isw - - 40 mA Input impedance |ZI| 50 - - kW Output power THD = 0,5%; 4 W Po - 5 - W THD = 10%; 4 W Po - 6 - W Channel separation a 40 - - dB Noise output voltage Vno(rms) - 150 - mV Supply voltage ripple rejection f = 100 Hz SVRR 40 - - dB f = 1 kHz to 10 kHz SVRR 48 - - dB Crystal temperature Tc - - 150 °C PACKAGE OUTLINE 9-lead SIL-bent-to-DIL; plastic (SOT110B); SOT110-1; 1996 July 19. May 1992 2 Philips Semiconductors Product specification Philips Semiconductors Product specification 9 Fig.1 Block diagram. May 1992 3 Philips Semiconductors Product specification Philips Semiconductors Product specification 9 PINNING 1 INV1 non-inverting input 1 2 GND1 ground (signal) 3 SVRR supply voltage ripple rejection 4 OUT1 output 1 5 GND2 ground (substrate) 6 OUT2 output 2 7 VP supply voltage 8 M/SS mute/stand-by switch 9 -INV2 non-inverting input 2 FUNCTIONAL DESCRIPTION The TDA1519 contains two identical amplifiers with differential input stages. The gain of each amplifier is fixed at 40 dB. A special feature of this device is the mute/stand-by switch which has the following features: · low stand-by current (< 100 mA) · low mute/stand-by switching current (low cost supply switch) · mute condition. RATINGS Limiting values in accordance with the Absolute Maximum System (IEC 134) PARAMETER CONDITIONS SYMBOL MIN. MAX. UNIT Supply voltage operating VP - 18 V non-operating VP - 30 V load dump protected during 50 ms; tr . 2,5 ms VP - 45 V AC and DC short-circuit-safe voltage VPSC - 18 V Reverse polarity VPR - 6 V Energy handling capability at outputs VP = 0 V - 200 mJ Non-repetitive peak output current IOSM - 4 A Repetitive peak output current IORM - 2,5 A Total power dissipation see Fig.2 Ptot - 15 W Crystal temperature Tc - 150 °C Storage temperature range Tstg -55 + 150 °C May 1992 4 Philips Semiconductors Product specification Philips Semiconductors Product specification 9 Fig.2 Power derating curve. DC CHARACTERISTICS (note 1) VP = 14,4 V; Tamb = 25 °C; unless otherwise specified PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT Supply Supply voltage range Quiescent current DC output voltage Mute/stand-by switch Switch-on voltage level Mute condition Output signal in mute position Stand-by condition DC current in stand-by condition Switch-on current note 2 note 3 see Fig.3 VI = 1 V (max.); f = 20 Hz to 15 kHz VP IP VO VON Vmute VO Vsb Isb Isw 6,0 - - 8,5 3,3 - 0 - - 14,4 40 6,95 - - - - - 12 18,0 80 - - 6,4 20 2 100 40 V mA V V V mV V mA mA May 1992 5 Philips Semiconductors Product specification 2 x 6 W stereo car radio power amplifier TDA1519 AC CHARACTERISTICS (note 1) VP = 14,4 V; RL = 4 W; f = 1 kHz; Tamb = 25 °C; unless otherwise specified PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT Output power note 4; THD = 0,5% THD = 10% Po Po 4 5,5 5 6,0 - - W W Total harmonic distortion Po = 1 W THD - 0,1 - % Low frequency roll-off note 5; -3 dB fL - 45 - Hz High frequency roll-off -1 dB fH 20 - - kHz Closed loop voltage gain Gv 39 40 41 dB Supply voltage ripple rejection note 6 ON f = 100 Hz SVRR 40 - - dB ON f = 10 Hz to 10 kHz SVRR 48 - - dB mute SVRR 48 - - dB stand-by SVRR 80 - - dB Input impedance |Zi| 50 60 75 kW Noise output voltage note 7; ON RS = 0 W Vno(rms) - 150 - mV ON RS = 10 kW Vno(rms) - 250 500 mV mute note 8 Vno(rms) - 120 - mV Channel separation RS = 10 kW a 40 - - dB Channel balance |DGv| - 0,1 1 dB Notes to the characteristics 1. All characteristics are measured using the circuit shown in Fig.4. 2. The circuit is DC adjusted at VP = 6 V to 18 V and AC operating at VP = 8,5 V to 18 V. 3. At 18 V < VP < 30 V the DC output voltage . VP/2. 4. Output power is measured directly at the output pins of the IC. 5. Frequency response externally fixed. 6. Ripple rejection measured at the output with a source impedance of 0 W (maximum ripple amplitude of 2 V) and a frequency between 100 Hz and 10 kHz. 7. Noise voltage measured in a bandwidth of 20 Hz to 20 kHz. 8. Noise output voltage independent of RS (VI = 0 V). May 1992 6 Philips Semiconductors Product specification Philips Semiconductors Product specification 9 Fig.3 Stand-by, mute and ON conditions. May 1992 7 Philips Semiconductors Product specification Philips Semiconductors Product specification 9 APPLICATION INFORMATION Fig.4 Appli...