Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
DIGITAL ANSWERER WITH CID 4313385 © 2006 ORBYX Electronics. All Rights Reserved. IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: 1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. 2. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 3. Do not use the telephone to report a gas leak in the vicinity of the leak. 4. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire. They may explode. Check with local codes for possible special disposal instructions. 5. Position the equipment near an electrical outlet that shall be easily accessible and plug the adapter into the outlet. SAVE THESE INSTRUCTIONS! INDUSTRY CANADA CS03 STATEMENT This product meets the applicable Industry Canada technical specifications. This is confirmed by the registration number. The abbreviation, IC before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry Canada approved the equipment. Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connections. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or alterations made by the user of this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment. WARNING! Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or an electrician, as appropriate. CAUTION: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. An alternative indication of the REN is the Load Number (LN); this number should be divided by 20 to approximate the equivalent REN. The REN Number of this unit is indicated on the bottom of your answering machine. INDUSTRY CANADA RSS 210 NOTICE: CLASS B LIMITS WITH INTERFERENCE STATEMENT This equipment complies with the limits of a Class B digital device as specified in Industry Canada Regulations. These limits provide reasonable protection against radio and TV interference in residential areas. However, this device might cause radio or TV interference even when it is operating properly. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference including interference that may cause undesired operation of the device. To eliminate the interference, you can try one or more of the following: • Reorient or relocate the receiving antenna. • Move your device away from the receiver. • Connect your device to an outlet that is on a different electrical circuit from the receiver. This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus. BATTERY NOTES Dispose of old battery promptly and properly. Do not burn or bury battery. Use only fresh battery of the required size and recommended type. If you do not plan to use the phone for two weeks or longer, remove the battery. Batteries can leak chemicals that can destroy electronic parts. To avoid losing stored information, be sure the system is properly connected to AC power before you replace the battery. Disconnect the telephone line cord before replacing the battery to reduce the risk of fire or injury. TM MC 1. Line Cord 2. Incoming Message Length Switch 3. Call Back Button 4. Display 5. Erase Button 6. Microphone 7. Volume Button 8. / OGM Button 9. Play / Pause button 10. Menu Button 11. Delete Button 12. Ringer Switch 13. Power Jack 14. Telephone Line Jack 15. New Call LED 16. Review Button 17. Review Button 18. Speaker 19. Message LED 20. / Time Check Button 21. Memo / 2 way Button 22. On / Off / Stop Button 23. Volume Button INSTALLATION TO INSTALL 9-VOLT BATTERY In the event of a power failure, a 9V alkaline battery (not supplied) is required to maintain your personalized outgoing announcement, recorded messages and CID data. If the battery is no...