Stimmen - 5, Durchschnittliche Bewertung: 4.4
(
)
)
|
Anleitung Zusammenfassung
If this happens, start over again at Step 1. 1. Press PGM/DEL. The TAD beeps once. illustration 43-781.fm Page 9 Monday, August 16, 1999 7:41 AM 2. Press 1/TIME. The TAD says “Press one for Monday. Press two for Tuesday. Press three for Wednesday. Press four for Thursday. Press five for Friday. Press six for Saturday. Press seven for Sunday.” illustration 3. Press a number button to set the day of the week. The TAD says the day of the week and “Enter the time.” 4. Press two digits for the hour. The TAD says the hour. Note: If you make an invalid entry (for example, 00 or 13), the TAD beeps three times and repeats “Enter the time.” 5. Press two digits for the minute. The TAD says the minute and “Press one for AM, two for PM.” Note: If you make an invalid entry (for example, 66), the TAD does not respond. Make a correct entry within 7 seconds. 6. Press 1 or 2. The TAD says the current day and time. To hear the current day of the week and time at any time, press TIME. SETTING THE NUMBER OF RINGS The TAD is preset to sound 4 rings before it answers the first call. Follow these steps to change the number of rings (from 2-9). Notes: • If you plan to check your messages by long distance, set the number of rings to at least four to avoid unnecessary long distance charges when you call by remote to check your messages (see “Using the Toll Saver”). • In Steps 2 and 3, you must enter your selection within 7 seconds. otherwise, the TAD beeps three times then exits the programming mode. If this happens, start over again at Step 1. illustration 1. Press PGM/DEL. The TAD beeps once. 2. Press 3/RING. The TAD beeps once. 3. Enter the number of rings you want (up to 9). The TAD repeats the number, then beeps twice. 9 43-781.fm Page 10 Monday, August 16, 1999 7:41 AM RECORDING ANNOUNCEMENTS Recording the Outgoing Announcement The TAD has a built-in outgoing announcement that says “Please leave your message after the tone.” You can record another announcement for the caller to hear when the TAD answers a call. The announcement can be up to 1 minute long. Important Hints: • We recommend you write down your announcement before recording it. If you plan to record callers’ messages, ask for the caller’s name, phone number, and message. • Do not tell callers that you are not home. Instead, say that you cannot come to the phone right now. Follow these steps to record your outgoing announcement. 1. Press and hold OGM (outgoing message) until the TAD beeps and the flashes. ON LINE indicator illustration 10 2. Release OGM and record your announcement. Speak into the TAD from about 12 inches away. Note: The outgoing message must be at least 2 seconds long for proper remote operation. 3. When you finish speaking, press ON/OFF. The TAD beeps once, the announcement plays, then the ON LINE indicator stops flashing and the TAD beeps once more. Note: To change the outgoing announcement, you can repeat these steps to record over the current one, or delete the current one so the TAD once again uses its built-in outgoing announcement (see “Checking/Deleting the Outgoing Announcement”). Checking/Deleting the Outgoing Announcement You can press OGM at any time to play the outgoing announcement. Adjust VOLUME on the side of the TAD to a comfortable listening level. To stop listening to the outgoing announcement before it ends, press ON/ OFF. To delete your recorded outgoing announcement, press PGM/DEL while the TAD is playing it. The TAD beeps twice and is then set to use its built-in announcement. 43-781.fm Page 11 Monday, August 16, 1999 7:41 AM Recording the Memory Full Announcement The TAD has a built-in memory full announcement. When the memory becomes full and the TAD can no longer record messages, the ON LINE, PLAY, and MEMO indicators flash, and the TAD announces to the caller “The memory is full.” Follow these steps if you want to record your own memory full announcement (up to 1 minute in length). 1. Press and hold 4/OGM2 until the TAD beeps and the ON LINE indicator flashes. illustration 2. Speak into the TAD in a strong voice from about 12 inches away. 3. Press ON/OFF when you finish recording the announcement. The TAD plays the current memory full announcement. Checking/Deleting the Memory Full Announcement You can press 4/OGM2 at any time to play the memory full announcement. Adjust VOLUME on the side of the TAD to a comfortable listening level. To stop listening to the memory full announcement before it ends, press ON/ OFF. To delete your recorded memory full announcement, press PGM/DEL while the TAD is playing it. The TAD beeps twice and is then set to use its built-in announcement. 11 43-781.fm Page 12 Monday, August 16, 1999 7:41 AM BASIC OPERATION Be sure you complete the procedures in “Installation” and “Preparation” before you begin using the TAD. SETTING THE TAD TO ANSWER/NOT ANSWER CALLS To set the TAD to answer calls, simply turn it on by pressing ON/OFF until the ON LINE indicator turns on. illustration Note: You can use a ...