Stimmen - 1, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Number of items A ........1 H ........6 F CAR DIVERSITY ANTENNA WITH BOOSTER CX-A330 ON OFF BOOST ........2 G ........1 E ........2 B ........4 C ........2 1. To prevent short circuits, remove the key from the ignition and disconnect the · terminal of the battery. 2. Make the proper input and output cable connections for each unit. 3. Connect the wiring harness cables in the following order: ground, battery, ignition. 4. Connect the wiring harness connector to the unit. 5. Install the unit in your car. 6. Reconnect the ·terminal of the battery. 7. Press the reset button. • If your car's ignition does not come with an ACC position, connect the ignition cables to a power source that can be turned on and off with the ignition key. If you connect the ignition wire to a power source that receives a constant voltage supply, as with battery cables, the battery may die. • If the fuse blows, first make sure that the cables have not caused a short circuit, then replace the old fuse with one with the same rating. • Do not let unconnected cables or terminals touch metal on the car or anything else conducting electricity. To prevent short circuits do not remove the caps from unused terminals or from the ends of the unconnected cables. • After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly. • Insulate unconnected wires with vinyl tape or other similar material. • Thoroughly wipe away oil and other dirt from the installation surface. Please avoid installation on uneven surfaces. • Mount the unit so that the mounting angle is 30° or less. 2CAUTION (M4 . 6mm) Installation Procedure D ........1 Installing the Main Uni t hen mounting the main unit after checking the operation, close the monitor first. During installation, do not use any screws except for those provided. The use of different Damage may occur if a screwdriver or similar tool is used with excessive force during the Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction. NOTE 2 CAUTION Metal mounting strap (Commercially available) Self-tapping screw (Commercially available) Firewall or metal support Screw (M4 x 8 mm) (Commercially available) Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Use the Hard Rubber Frame (Accessory D). ¦ Installing in Japanese-Made Cars-1 When the vehicle bracket is attached as in Toyota, Nissan, Mitsubishi, and other vehicles that use a hole in the . position in Not use the Hard the figure below. Rubber Frame (Accessory D). or Audio Unit.etc Accessory B Screw (Provided with the Audio Unit.etc) Screw (Provided with the Audio Unit.etc) Accessory B Installing the Main Unit ¦ Installing in Japanese-Made Cars-2 or Accessory B Accessory B Accessory C Accessory C When the vehicle bracket is attached as in Toyota vehicles that use a hole in the . position in the figure below. 1 Fasten Accessory C on both sides as shown in the figure below. 2 Fasten the vehicle bracket. 3 Bend the point of Accessory C, and fasten the bracket. If this device can’t be fastened with screws in the 2 places on the right and left due to the vehicle bracket shape, use the installation fastener (Accessory C) and fasten the bracket. Using a screwdriver or pliers bend the right and left of Accessory C so that it can be fastened to the vehicle bracket hole. Not use the Hard Rubber Frame (Accessory D). Audio Unit.etc Screw (Provided with the Audio Unit.etc) Screw (Provided with the Audio Unit.etc) 4 Installing and Connecting the Antenna Unit s • Attach the antenna to the inner glass surface of the rear window using double-sided tape. Carefully check the installation location as the tape can only be stuck on once. • If the surface temperature of the glass of the rear window is low, warm it by turning on the power of the rear defogger. A cold window glass surface will weaken the adhesive strength of the double-sided tape. Also, if installat...
Dieses Handbuch ist für folgende Modelle:Car Video - VZ-7000P (312.21 kb)