Stimmen - 5, Durchschnittliche Bewertung: 3.6 ( )

Hersteller: Wayne Dateigröße: 1.07 mb Dateiname: 307532%20Rev3.pdf Unterrichtssprache:

THIS MANAUL SHOULD BE ATTACHED IN CLOSE PROXIMITY TO THE GARAGE DOOR OPENER. DOOR AND OPENER WILL NOT OPERATE PROPERLY UNTIL INFRARED SAFETY SENSORS ARE INSTALLED AND PROPERLY ADJUSTED! DO NOT OPERATE DOOR OPENER UNTIL FULLY INSTALLED, ADJUSTED & INSTRUCTED TO DO SO! © Copyright 2003 Wayne-Dalton Corp. Part No: 307532 Rev3 10/15/03 Read These Important Safety Rules Before Proceeding This symbol indicates caution and appears throughout this instruction manual. This garage door opener is designed and tested to offer reasonably safe operation if installation is followed in strict accordance with these safety instructions. Failure to comply with these instructions may result in serious personal injury or property damage. IMPORTANT INSTALLATION INSTRUCTIONS WARNING: To reduce the risk of severe injury or death: READ AND FOLLOW ALL INSTALLATION IN-Do not connect opener to source of power until STRUCTIONS. instructed to do so. Install only on a properly balanced garage door. Installation and wiring must comply with local An improperly balanced door could cause severe building and electrical codes. Connect the power injury. Have a qualified service person make re cord to a properly grounded outlet. Do not repairs to cables, spring assemblies and other move round ground pin from power cord. hardware before installing opener. Install entrapment warning label next to control To reduce the risk of injury to persons, use this button in a prominent location, such as the inside operator only with sectional overhead doors. of the garage door, or as instructed in the installation instructions. If label adhesive will not adhere Fiberglass, aluminum and steel doors must be re- to the surface, secure the label by additional meinforced to prevent damage to the door. Check chanical means such as staples, nails or screws. with your garage door manufacturer for their rec-If necessary, use an intermediate mounting surommendations. face, such as plywood, cut to the appropriate size. Install Emergency Release tag to the emergency Remove all ropes and remove or make inoperative red cord. all locks connected to the garage door before installing opener. After installing opener, the door must reverse when it contacts a 1 inch high solid test object on Do not use sensitivity adjustments to compensate the floor. for a poorly operating door. This will interfere with the proper operation of the safety reverse Open door must not close and closing door must mechanism and may damage the door. open if photoelectric system in obstructed by 6” High object, using test procedure described in Locate control button: within sight of door, at a Step 29. minimum height of 5 feet, so small children cannot reach it, and away from all moving parts of the Do not wear rings, watches or loose clothing door. when installing or servicing a garage door sys tem. Use a sturdy, non-metallic step ladder. If possible, install door opener 7 feet or more above floor. Mount the emergency release knob 6 feet above the floor. AFTER INSTALLATION IS COMPLETE, FASTEN THIS MANUAL NEAR GARAGE DOOR. PERFORM PERIODIC SAFETY CHECKS, MAINTENANCE AND ADJUSTMENTS, AS RECOMMENDED. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Warning: Changes or modifications to this unit not expressly approved by Wayne-Dalton Corp. could void the user’s authority to operate the equipment. FCC Regulatory Information: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Regulatory Information: This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including ...

Herunterladen

Geben Sie zwei Ziffern: