Stimmen - 3, Durchschnittliche Bewertung: 4.7
(
)
)
|
Anleitung Zusammenfassung
1 2 3 Screws (4) Mount the Control Box Secure the control box to mounting surface (post, wall, column, etc.) using appropriate hardware (not provided). Install the Control Board Attach antenna. Reinstall batteries, control board, alarm, and reset button. Reconnect coaxial connector. NOTE: Make sure battery leads are on the left side of the control box and not pinched. Installation 22 4 5 Antenna U-Bolt (Not Provided) Wall Concrete Anchor Square Gate Post Screw 18 L1 K2 Z22 F2 MOV1 D1 OPEN SINGLE BUTTON RESET STOP CHGR OVLD COM COM D129 Z4 D2 C11 C13 D16 F9 K1 F3 K4 K3 F1 Z12 GATE 2 GATE 1 GR WH YL BL RD BR GR WH YL BL RD BR F7 24V CTRL OVLD TIMER RUNNING GATE 2 SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS GATE 1 LEARN XMITTER LOCK / ON OFF C69 PWR AC PWR /SOLAR R329 R27 MOV2 R4 C2 BIPART DELAY LOCK Q9 R9O F8 C73 C72 C71 C7O R42O R423 J24 J23 3OA 32V 3OA 32V J21 30 30 C64 U2 R22 K6 JU1 JU1 JU2 DB1 R184 ALARM K2 Z22 F2 MOV1 D1 D129 Z4 D2 C11 C13 D16 F9 K1 F3 K4 K3 F1 Z12 GATE 2 GR WH YL BL RD BR F7 24V GATE 2 SET OPEN LIMIT SET CLOSE LIMIT C69 R329 R27 MOV2 R4 C2 Q9 R9O F8 R42O R423 J24 J23 3OA 32V 3OA 32V J21 30 30 C64 U2 R22 K6 JU1 JU2 DB1 Screws Screws Screws Control Board Reset Button Connections Coaxial Connector Alarm Z22 CHGR OVLD CTRL OVLD PWR AC PWR /SOLAR MOV2 R4 C2 R184 Z22 MOV2 R4 C2 Screws Gate Moving Can Cause Injury or Death KEEP CLEAR! Gate may move at any time without prior warning. Do not let children operate the gate or the play in gate area. only This entrance is for vehicles Pedestrians must use separate entrance L1 R1 R2 Z1 K5 K6 K2 F3 10A 32V D1O P1 Z9 Z8 F2 F6 D4 D2 R9 C64 JMPR1 U4 FORCE TIMER TO CLOSE OFF MAX FUSE OPEN R35 D9 Z3 Z4 U3 D1 D27 F5 C11 C13 C12 D15 R4 C2 R1O1 R1OO R9O K1 Q9 R196 Q22 D8 K3 K4 D21 D22 C4 ACCESSORY OVLD D6 JMPR2 MOV1 MOV2 DB1 U2 Z12 24 VAC/ SOLAR INPUT GATE 2 ACCESSORY POWER MAGLOCK ALARM GATE 1 C C NC NO NO GRN WHT YEL BLU RED BRN GRN WHT YEL BLU RED BRN F4 10A 32V F7 24V TIMER RUNNING GATE 2 SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS DIAGNOSTIC GATE 1 J4 LEARN XMITTER MAGLOCK ON OFF Control Box 18 R93 D42 K2 D1O Z22 P1 F2 MOV1 D1 Q12 U4 D129 Z4 U3 D2 D44 C11 C13 D16 F9 R1OO R1O1 K1 Q22 F3 K4 K3 R196 F1 Z12 GATE 2 GR WH YL BL RD BR F7 24V GATE 2 SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS GATE 1 C69 J2O D8 D4 R9 R329 R27 MOV2 R4 C2 Z1 R2 K5 F12 Q9 R9O F8 Q6 Q1 C75 C73 C72 C71 C7O C66 C65 C68 C33 F11 R42O R423 J24 J23 3OA 32V 3OA 32V J21 30 30 C64 U2 R22 J18 K6 JU1 JU2 DB1 D36 23 Wiring Insert Operator Cable Insert watertight connector into the bottom of the control box and tighten with nut. Insert operator cable through watertight connector mounted in the bottom of the control box. To reduce the risk of SEVERE INJURY or DEATH: • ANY maintenance to the operator or in the area near the operator MUST not be performed until disconnecting the electrical power and locking-out the power via the operator power switch. Upon completion of maintenance the area MUST be cleared and secured, at that time the unit may be returned to service. • Disconnect power at the fuse box BEFORE proceeding. Operator MUST be properly grounded and connected in accordance with local electrical codes. NOTE: The operator should be on a separate fused line with a 15 amp circuit breaker. • ALL electrical connections MUST be made by a qualified individual. • DO NOT install ANY wiring or attempt to run the operator without consulting the wiring diagram. We recommend that you install an optional reversing edge BEFORE proceeding with the control station installation. • ALL power wiring should be on a dedicated circuit and well protected. The location of the power disconnect should be visible and clearly labeled. • ALL power and control wiring MUST be run in separate conduit. • BEFORE installing power wiring or control stations be sure to follow ALL specifications and warnings described below. Failure to do so may result in SEVERE INJURY to persons and/or damage to operator. ATTENTION AVERTISSEMENT AVERTISSEMENT AVERTISSEMENT WARNING CAUTION WARNING WARNING PRECAUCION ADVERTENCIA ADVERTENCIA ADVERTENCIA WIRING Connect Gate Operator (Gate 1) to Control Box 1 2 Operator Cable Watertight Connector Nut Operator Cable Watertight Connector Watertight Connector Watertight Connector Nut Nut Watertight Connector Nut Insert operator cable through watertight connector nut. Wiring 24 Connect Operator to Control Board Extend operator cable and wires to GATE 1 connector and connect as shown. Tighten watertight connector nut. Moving Gate Can Cause Injury or Death KEEP CLEAR! Gate may move at any time without prior warning. Do not let children operate the gate or play in the gate area. This entrance is for vehicles only Pedestrians must use separate entrance Z22 R91 CLOSE EDGE R94 R92 R93 L1 R1 R2 Z1 K5 K6 K2 F3 10A 32V D1O OPEN EDGE/ PHO T O OPEN PHO T O CLOSE PHO T O R227 R2O7 Z2 O R223 P1 Z9 Z8 F2 F6 D4 D2 R9 C64 JMPR1 R224 U4 CONTROL INPUTS FORCE TIMER TO CLOSE OFF MAX OPEN SINGLE BUTTON RESET STOP SHADOW INT...
Dieses Handbuch ist für folgende Modelle:Safety Gate - RESIDENTIAL GATE OPERATOR GA420D (9.54 mb)