Stimmen - 3, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Mount upper wall plate using two wood screws in the top template position marked in Step 1 (see Figure E). Step 6: Choose direction you want the gate to open, based on Figure F. WARNING: THE GATE SHOULD NOT OPEN OVER THE STAIRS. Position upper stop plate onto upper latch plate so that stop plate wall faces stairs, as show in Figure C. rj £1 Step 7: Locate upper latch with alarm and remove battery compartment door with Phillips head screwdriver. Install 2 AAA batteries (included) into back of unit as shown in Figure H. Screw battery door back onto upper latch. Step 14: Assemble the spring onto the lower hinge post. Place the lower hinge cap over the spring and lower hinge spindle. Slide the lower hinge cap into place and secure with a wood screw. Ensure that the hinge is oriented as shown in Figure Q. Note: You must maintain equal spacing between walls and outer most panel bars. This space should not exceed 3" on NOTE: If Panel B is not needed, skip steps 15 and 16. Step 8: Snap upper latch with alarm onto upper latch plate assembly as shown in Figure I. Secure in place with the four provided alarm screws. Step 9: Choose the lower cup whose larger side faces stairs. Insert lower latch into lower cup and mount to wall using two wood screws at the bottom template position marked in Step 1. Be sure that the spindle rest opening faces up as shown in Figure J. NOTE: The remaining wall cup should be stored for future use. Step 10: Measure the width of the opening where you intend to install the gate. Please refer to the following pictures to determine the correct installation configuration. Final size adjustment must be made by individually adjusting the spindles. If opening is 28" - 30.5" wide, only Panel A is needed. If greater than 30.5" wide, use Panel A and Panel B. Step 11: Screw the upper and lower hinge spindles into the hinge side of ends of Panel A's ends until they stop as shown in Figure M and N. Step 12: Adjust the upper hinge spindle out until it can fit onto the hinge post on the upper hinge as shown in Figure O. Step 13: Adjust the lower hinge spindle out until it can fit onto the hinge post on the lower hinge as shown in Figure R Place spindles of both hinges down into position simultaneously. Step 15: Align Panel B over Panel A allowing an approximately 2" gap between Panel B and the doorway. Step 16: To use with an extension Panel B, assemble as shown in Figure R. Align the adjustment screw holes in the top rails of extension A and B with a minimum overlap of 2 post screw holes, as shown in Figure R. Insert the post screw receivers into two aligned holes; insert and tighten post screws securely, as shown in Figure S. Now repeat this procedure for the bottom two rails ensuring that they are securely tightened. (28" - 30.5") with ftinel A (30.5" - 54") with Panels A & B Step 17: Screw upper and lower latch spindles into end of outermost panel as shown in Figure T and U. Step 18: Adjust the upper and lower latch spindles outward until they fit into the spindle rests on the latches, as shown in Figures V & W. Do not over adjust spindles (too tight against latches) or gate will be difficult to open. r\ 1 ■ 91 iL Jl jj w Step 19: Cap open ends of panels with a threaded end screw as shown in Figure X. Step 20: Using the wrench, tighten each (4 total) spindle lock nut inward toward the gate until they are secure. Do not over tighten. Check to ensure that all connections are secure and that gate is properly installed. either side. OPERATION: To opon the goto without triggering alarm: (see Figure Y) Push button on top of alarm unit. This will delay alarm for 10 seconds. Open gate by rotating the thumb latch on the upper latch. Then lift gate out of the upper and lower spindle rests and swing open. NOTE: If you do not push the button on alarm unit, alarm will sound until the gate is closed. To close the gate: Simply swing the gate and it should close shut automatically. ALWAYS check that the latch is securely fastened that all connections are fastened securely. NOTE: If gate is not closed within 10 seconds, alarm will sound for 3 minutes or until the gate is closed. To use without alarm: Remove batteries. Troubleshooting: If the gate does not stay closed: 1« The upper latch spindle Is not adjusted properly. Solution: Adjust the upper latch spindle by loosening the spindle lock nut with the wrench. Make certain that the spindle is properly adjusted to fit in the upper latch spindle rest. Secure the lock nut. Make sure that the upper latch spindle is properly locked onto the upper latch with the thumb lock. 2. Spindles adjustments are unequal. Solution: Although unusual, some doorframes may be out of alignment. In this case you may have to adjust the individual spindles to ensure that the gate is aligned properly. Make sure that the upper latch spindle properly locks into the upper latch. If the gate does not stay in position it may not be installed prop...