Stimmen - 3, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
Keep this instruction manual for future reference. Tools required: Phillips head screwdriver (not included). For Technical Support Call 1 -800-268-6237 or E-Mail at customerservice@summerinfant.com AWARNING: This product contains small parts. Adult assembly required. Exercise care when unpacking and assembling product. For use with children birth and up. INSTRUCTION MANUAL_ SURE AND SECURE™ DELUXE WOOD WALK-THRU GATE Thank you for buying the Sure and Secure™ Deluxe Wood Walk-Thru Gate from Summer Infant. This pressure-mounted sate helps you create and maintain a secure environment for your child. It has a hinged swinging door that opens easily in either direction with one hand. It also swings closed automatically. It’s fully adjustable to fit openings from 29.5"- 40.5". In normal use there is no need for mounting holes that damage woodwork and walls. For added security use the mounting cups and screws that are provided. Please read all the instructions before installing the gate. AWARNING: IMPORTANT! KEEP FOR FUTURE REFERENCE) To prevent serious injury or death, securely install gate and use according to manufacturer’s instructions. Never use with a child able to climb over or dislodge the gate. Never leave child unattended. Use only with lock securely engaged. Do not use if any components are missing or damaged. To prevent falls never use at top of stairs. This product will not necessarily prevent all accidents. Proper adult supervision is required at all times. A CAUTION ! KEEP SMALL PARTS OUT OF CHILD'S REACH. FEATURES & COMPONENTS: Latch Set Gate Panel Gate Frame Extension Frames (two) Tension Bolts (four) Mounting Cups (four) Adhesive Mounting Pads (four) Extension Pins (four) Screws (four) Wall Anchors (four) Wrench w SET UP Measure the width of the opening where you intend to install the gate. Please refer to the following pictures to determine the correct installation configuration. FIGURE^ FIGURE! FIGURE« (291A>" -331/2") without Extension Frame (33V21 - 37V21) with Extension Frame (37W - 40.5") with Extension Frame To use with extension frame assemble as shown in Figure D. €» Screw the tension knobs down the tension bolts until they contact the pads. Insert 4 tension bolts into holes on outside and slide inward towards frame as far as possible. OPERATION: Center the sate in the opening, so that the distance from the bottom of gate frame to each side wall is equal, as shown in Figure H. Use the marks etched into the wrench as a ruler. Slide the tension bolts out until the pads contact the doorframe or wall. Then screw the tension knob away from the pad until it contacts the gate frame as shown in Figure I. !...... ! Distance should be equal FIGURE O FIGURE« Tighten both of the tension knobs on the bottom inward towards the frame at the same time, as shown in Figure J. Then tighten both of the tension knobs on the top inward towards the frame at the same time, as shown in Figure K, so that the upper latch set goes below the release button completely, as shown in Figure M. To verify installation: Push the frame to ensure that it is secure in the opening and then push the gate panel to ensure that the upper and lower latch sets lock securely in the housings on the frame, as shown in Figures L and M. FIGURE« Note: Wrench is provided for final tightening of all four tension knobs (if necessary), as shown in Figure G. FIGURE o Note: If gate is difficult to unlatch, top tension knobs may be too tight. To open the gate: (see Figure N) 1. slide the release button away from the door frame or wall 2. lift up the gate panel 3. swing open in either direction To close the sate: Simply release the gate and it will close automatically. Caution: After closing the gate, ALWA/S check to be certain that it is latched securely FIGURE o o°/* an Troubleshooting If the gate does not stay closed: 1. The Upper latch set is not properly adjusted. Solution: Adjust the upper tension knobs by turning them counter-clockwise to release tension or clockwise to increase tension. Ensure that the upper latch set button always remains below the release button as shown in Figure M. Also ensure that the upper latch set button engages securely when the gate swings closed and that it can be released properly when the release button is pushed. 2. Lower latch set position is too low. Solution: Although unusual, some door frames may be out of alignment. In this case you may have to adjust the individual tension knobs to ensure that the gate is aligned properly. Make sure the upper latch set is still below the release button as shown in Figure M. If the gate does not stay in position it may not be installed properly as shown in Figure M. Remove and reinstall the gate, making sure the gate is installed correctly as shown in Figure O. FIGURE MAINTENANCE: 1. Regularly check tension knobs and rubber pads to make sure the gate is securely in place. 2. Do not use the gate if any component...