Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Wayne-Dalton Dateigröße: 9.73 mb Dateiname: Unterrichtssprache:

This will prevent the door from raising or lowering while installing the rear support. Using perforated angle, 2” lag screws and 5/16” bolts with nuts (may not be supplied), fabricate rear support for horizontal tracks. Attach horizontal tracks to the rear supports with 5/16”-18 x 1-1/4” hex bolts and nuts (may not be supplied). Horizontal tracks must be level and parallel with door. ^WARNING! KEEP HORIZONTAL TRACK PARALLEL AND WITHIN 3/4” OF DOOR EDGE, OTHERWISE DOOR COULD FALL, RESULTING IN SEVERE OR FATAL INJURY Permanently attach the vinyl weather stripping to both doorjambs and the header, Fig. 5C. Now, lift the door and check it’s balance. Adjust, if door lifts by itself (also hard to pull down) or if door is difficult to lift (too easy to pull down). Anytime spring adjustments are made you must loosen the lock nuts to begin with and retighten both lock nuts afterwards. To adjust spring(s), only add or remove 1/4 turn on the counter reading at a time. Adjust both sides equally. IMPORTANT! Do not add or remove more than 1 spring turn from specified amount. If the door still does not operate easily, lower the door into the closed position, UNWIND SPRING(S) TO ZERO, and recheck the following items: 1.) Check the door for level. 2.) Check the TorqueMaster™ tube and flagangles for level and plumb. 3.) Check the distance between the flagangles - must be door width plus 3-3/8” to 3-1/2”. 4.) Check the counterbalance cables for equal tension - loosen set screws and adjust if necessary. 5.) Rewind the spring(s). 6.) Make sure door isn’t rubbing on jambs. NOTE: As a safety feature, the right hand end bracket on single spring applications, both right hand and left hand end brackets double springs applications, cannot be disassembled for service until the spring(s) is completely unwound and the counter cover reads zero. After door installation is completed, refer to the /drive™ owner’s manual, starting at the PRE-OPERATION INSTALLATION section to complete the opener installation. If there are stiles or lite frame dividers included with your door, install them per their instructions at this time. ALTERNATE INSTALLATIONS If you are not installing the /drive™ operator on your garage door, you must install the center bracket bushing assembly. Follow these instructions for a non-/drive™ operated garage doors. TorqueMaster™ springs come lubricated and pre-assembled inside the torque tube. To install, lay the torque tube on the floor in front of the door with the labeled end to the left. Slide the center bracket/bushing assembly onto the torque tube, from the right hand side, toward the center. Shake the TorqueMaster™ tube gently to extend the winding shafts out about 5” on both ends. Single spring TorqueMaster will only have the right hand spring. Slide center bracket bushing assembly from the right side to the center of the torque tube. IMPORTANT! Right and left hand is always determined from inside the building looking out. TYPICAL TROLLEY OPERATOR INSTALLATION If you are installing an electric operator on your door, the following information is provided to ensure proper function of your door/operator installation. Figure below shows a typical means of connecting the operator arm to the operator stile located in the center of the top section. When installing a DoorMaster™ operator replace the bushing with the drive gear (located in DoorMaster™ package). © To locate the center bracket, mark the header halfway between the flagangles and level the TorqueMaster tube, ten the metal bracket to the header using (2) 1/4” x 1-1/2” lag screws. Fas- cc OPTIONAL ACCESSORY INSTALLATIONS (OUTSIDE) (INSIDE) Raise the door to a comfortable working height and secure with locking pliers to the track. Locate the center stile on the bottom section of the door. Using the pre-punched holes at the bottom of the stile as a template, drill (2) 7/32” (6mm) dia. holes through the section. Using the previously drilled holes as a guide, enlarge the holes from outside the door to 7/16” (11mm) dia. and assemble the outside and inside step plates to the section using (2) #8 x 1-5/8” screws. NOTE: Do not drill through or enlarge holes on the inside of the door. Awarning: TO AVOID SERIOUS INJURY TO FINGERS OR HANDS, NEVER PLACE FINGERS OR HANDS BETWEEN DOOR SECTIONS AND TRACK WHEN OPERATING DOOR. ALWAYS USE STEP PLATE WHEN MANUALLY OPER-ATING DOOR. PULL ROPg Attach No. 6 screw eye to wood jamb approximately 48” - 50” (1220 - 1270 mm) off the floor. Use (1) 1/4”-14 x 5/8” selftapping screw to fasten pull rope clip to the end stile and then tie the pull rope to both the screw eye and the pull rope clip. &WARNING! DO NOT INSTALL PULL ROPE ON DOORS WITH ELECTRIC OPERATORS. CHILDREN MAY BECOME ENTANGLED IN THE ROPE RESULTING SEVERE OR FATAL INJURY DRILL THROUGH SECTION WITH A 7/16” (11mm) DIA. DRILL BIT Î (2) #8 x 1-5/8” SCREWS N0.6 SCREW EYE , ÇÎNSIDE SIDE LOCj^ Select desired side of door for lock placement. Locate ...

Herunterladen

Geben Sie zwei Ziffern: