Stimmen - 1, Durchschnittliche Bewertung: 3
(
)
)
|
Anleitung Zusammenfassung
NO ONE SHOULD ENTER OR LEAVE GARAGE WHILE DOOR IS IN MOTION. DO NOT ALLOW CHILDREN TO OPERATE REMOTES OR DOOR CONTROL BUTTONS. DO NOT ALLOW CHILDREN TO PLAY NEAR THE DOOR. Your garage door opener receiver and remote control transmitter have been set at the factory to a matching code. If you want to CHANGE your code or purchase additional remotes, follow the Instructions below. The code in any NEW remote control must be set to match the code in the original remote control. MATCH/CHANGE THE CODE IN REMOTE CONTROL(S) SET CODE SWITCHES IN ALL REMOTES TO MATCHING POSITIONS PROCEDURE: Slide battery compartment cover back to access the code switches in your single function remote control and any new remote control Place remote controls side by side as shown and set code switches in ALL remotes to matching positions (+, -, 0). Use a pen or screwdriver to slide the switches. NOTE: Instructions for matching the code switches in two-channel and multi-function remote control transmitters are included with those accessories. MATCH/CHANGE THE CODE IN THE RECEIVER GARAGE DOOR OPENERS WITH RECEIVER SMART CODE BUTTON 1. Press the RECEIVER Smart Button on the back panel of the opener as shown The adjacent indicator light will turn ON. CAUTION: Door will begin to move immediately if any transmitter has been activated. If this occurs, wait until the door has completed its UP or DOWN cycle. Then begin again at Step 3. 2. STAND AWAY FROM THE DOOR and press the remote Push Button control transmitter push button The indicator light will turn OFF REMOTE CONTROLTRANSMITTER and the door will move. Receiver and remote control(s) codes now match. The opener will operate when either the door control button or the remote control transmitter push button is pressed NOTE: If the remote control transmitter push button is not pressed within 30 seconds, the indicator light will turn OFF. In that case, begin again at Step 1. 23 Repair Parts RAIL ASSEMBLY PARTS LIST Master Link Kit 1A995 Chain Pulley Bracket 41A2780 Full Chain Assy. 41D384 NOT SHOWN Owners Manual 114A1225 One-Piece T-Rail 183B99 Inner Trolley w/Rod 41B3243 Outer Trolley 41B3244 1 2 3 4 6 5 7 INSTALLATION PARTS LIST Lighted Push Button Assembly 41A2756 Remote Control Transmitter Case, Cover & Screw Assembly (circuit board not included) 41A3593 12V Battery 10A14 2 Strand Bell Wire 217A238 4 Strand Bell Wire 217A241 Multi-Function Control Panel 41A3586 Door Bracket 12B374 Door Bracket Plate 12B380 Header Bracket Plus Clevis and Fastener 41A2829 Emergency Rope & Handle Assembly 41A2828 Curved Door Arm Section 178B35 Remote Control Transmitter Visor Clip 29C128Straight Door Arm Section 178B34 8 9 14 10 11 15 12 16 17 13 18 19 26 Repair Parts Chassis Assembly Parts List KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 1 41A3260 Sprocket cover with screw and idler pulley 12 41D3058 Universal replacement motor & bracket assy. (1156, 1146) Complete with: Motor, worm, bracket, 31C290 Sproket cover (1160, 1155, 1145, 1140) bearing assembly RPM sensor 2 41A3261 41A2827 3 41A2817 4 41B2991 Gear and sprocket assy. (1156, 1146) Gear and sprocket assy. (All other models) Complete with: Spring washer Thrust washer Retaining ring Bearing plate Roll pins (2) Drive gea...
Dieses Handbuch ist für folgende Modelle:Safety Gate - 1145- 1/3HP (1.25 mb)
Safety Gate - 1146 - 1/3HP (1.25 mb)
Safety Gate - 1150- 1/3HP (1.25 mb)
Safety Gate - 1156- 1/2HP (1.25 mb)