Stimmen - 6, Durchschnittliche Bewertung: 3.8 ( )

Hersteller: Chamberlain Dateigröße: 4.17 mb Dateiname: Unterrichtssprache:

Force Adjustment Controls are located on rear panel of opener. FORCE ADJUSTMENT settings regulate amount of the power required to open and close door. NOTE: The door STOPS in the UP direction if anything interferes with its travel. Door REVERSES in the DOWN direction if anything interferes with its travel (including binding or unbalanced doors). If the force adjustments are set too light, door travel may be interrupted by nuisance reversals in DOWN direction and stops in UP direction. Weather conditions can affect the door movement, so occasional adjustment may be needed. Maximum force adjustment range is 260 degrees, about 3/4 of a complete turn. Do not force controls beyond that point. Turn force adjustment controls with a screwdriver. Adjustment Label FORCE ADJUSTMENT CHART TEST DOWN (CLOSE) FORCE Grasp the door handle or door bottom when door is about halfway through DOWN (CLOSE) TRAVEL. Door should reverse. If the door is hard to hold or doesn't reverse, decrease DOWN (CLOSE) FORCE by turning the control in a counterclockwise direction. Make 10 degree turn adjustments until door reverses normally. After each adjustment, run opener through a complete cycle. PROCEED TO STEP 3 IF DOOR DOESN'T OPEN AT LEAST 5 FEET Increase UP (OPEN) FORCE by turning the control in a clockwise direction. Make 10 degree turn adjustments until door opens completely. Readjust UP LIMIT if necessary. After each adjustment, run opener through a complete travel cycle. IF DOOR REVERSES DURING DOWN (CLOSE) CYCLE Increase DOWN (CLOSE) FORCE by turning control clockwise. Make 10 degree turn adjustments until door completes close cycle. After each adjustment, run the opener through a complete travel cycle. 21 ADJUSTMENT STEP 3 Test Safety Reverse System THE SAFETY REVERSE SYSTEM TEST IS IMPORTANT. GARAGE DOOR MUST REVERSE ON CONTACT WITH A ONE-INCH OBSTACLE PLACED ON THE FLOOR. FAILURE TO PROPERLY ADJUST OPENER MAY RESULT IN SERIOUS PERSONAL INJURY FROM A CLOSING GARAGE DOOR. REPEAT TEST ONCE A MONTH AND ADJUST AS NEEDED. REPEAT ADJUSTMENT STEP 3 AFTER: • EACH ADJUSTMENT OF DOOR ARM LENGTH, CLOSE FORCE OR DOWN LIMIT. • ANY REPAIR OR ADJUSTMENT OF GARAGE DOOR (INCLUDING SPRINGS AND HARDWARE). • ANY REPAIR OR BUCKLING OF THE GARAGE FLOOR R. • ANY REPAIR OR ADJUSTMENT OF THE GARAGE DOOR OPENER. PROCEDURE: Place-a one-inch obstacle on the floor under the garage door. Operate door in DOWN direction. The door MUST reverse on the obstruction. If the door STOPS on the obstruction, it is not traveling far enough in the DOWN direction. Increase the DOWN limit by turning DOWN limit adjustment screw counterclockwise 1/4 turn. REPEAT TEST. NOTE: Make sure limit adjustments do not force the door arm beyond a straight up and down position. See the illustration on Page 18/19. When the door reverses on the one-inch obstacle, remove the obstruction and run the opener through a complete travel cycle. Door MUST NOT reverse in closed position. Repeat Adjustment Steps 1, 2 and 3 if necessary. THE PROTECTOR SYSTEMa Installation of Optional Safety Feature THE PROTECTOR SYSTEMa PROVIDES AN ADDITIONAL MEASURE OF SAFETY AGAINST A SMALL CHILD BEING CAUGHT UNDER A GARAGE DOOR. It uses an invisible beam which, when broken by an obstruction, causes a closing door to open and prevents an open door from closing. STRONGLY RECOMMENDED FOR HOMEOWNERS WITH YOUNG CHILDREN. After opener has been installed and adjusted, THE PROTECTOR SYSTEM accessory can be installed. Instructions are included with this optional device. 22 Radio Controls F.C.C. rules prohibit adjustments to or modification of receiver and/or remote control transmitter circuitry except for changing code setting and replacing remote control transmitter battery. NO USER SERVICEABLE PARTS. Manufactured under 1 or more of the following U.S. patents: RE29,525; 4,750,118; 4,8e8,930. Other Patents Pending. ACTIVATE THE OPENER ONLY WHEN DOOR IS IN FULL VIEW, FREE OF OBSTRUCTION AND PROPERLY ADJUSTED. NO ONE SHOULD ENTER OR LEAVE GARAGE WHILE DOOR IS IN MOTION. DO NOT ALLOW CHILDREN TO OPERATE REMOTES OR DOOR CONTROL BUTTONS. DO NOT ALLOW CHILDREN TO PLAY NEAR THE DOOR. Your garage door opener receiver and remote control transmitter have been factory set to a matching code. If you want to CHANGE your code or purchase additional remotes, follow the Instructions below. The code in any NEW remote control must be set to match the code in the original remote control. MATCH/CHANGE THE CODE IN REMOTE CONTROL(S) 1. Slide battery compartment cover back to access code switches in your single function remote and any new remote control. 2. Place remotes side by side as shown and set switches in ALL remotes to matching positions (+, -, 0). Use a pen or screwdriver to slide the code switches. NOTE: Instructions for matching the code switches in two-channel and multi-function remote control transmitters are Included with those accessories. MATCH/CHANGE THE CODE IN THE RECEIVER GARAGE DOOR OPENERS WITH RECEIVER "SMART" CODE BUTTON 3....

Herunterladen

Geben Sie zwei Ziffern: