Stimmen - 1, Durchschnittliche Bewertung: 4 ( )

Hersteller: Quantum Dateigröße: 720.73 kb Dateiname: UniversalQuantumManual-307545.pdf Unterrichtssprache:

Check with your garage door manufacturer for their recommendations. Reinforce light weight doors, as illustrated. For wood doors, mount door bracket, using two 1/4”-20 x 2” carriage bolts and 1/4” nuts supplied, on center line of door with middle hole in line with top rollers. For metal doors, mount door bracket, using two 1/4”-20 x 1/2” self drilling screws supplied, on center line of door with middle hole in line with top rollers. Step 7: Installing Light Remove diffuser cover by pressing on both sides of the bottom of the lighting cover at the junction of the housing, releasing the locking tabs, and pulling forward. Screw a 60 Watt bulb (60 Watt Maximum) into socket. For maximum bulb life, “rough service” bulbs are recommended. Align top and bottom tabs on cover to Motor Power Head Unit and push straight on until cover locks into place. Note: light turns on automatically when door is activated and a 4 minute time delay circuit automatically turns light off, allowing ample time to enter the house. A fully open door with light blinking indicates an obstruction or problems with external safety sensors during close travel. See trouble shooting section for further details. Step 8: Installing Wired Wall Station (if included) Install all wall controls out of the reach of children and in a location where the door can be seen before activating. Do not mount wall controls near or next to garage door. Wired Wall Station: Wire the garage door opener wall station using bell wire (low voltage electrical wire) connected to COM and P.B. on vertical screw terminal strips, as illustrated. Locate push button adjacent to service entrance door at a minimum height of 5 ft., and at least 5 ft. away from garage door; (see illustration in Step 10); additional wired wall stations may also be installed in accordance with these instructions. 8 Step 9: Installing Deluxe Wireless Wall Station (if included) Install all wall controls out of the reach of children and in a location where the door can be seen before activating. Do not mount push buttons near or next to garage door. Locate a convenient place to mount wall station. To keep wall station out of the reach of children, measure at least five feet up from the floor and secure wall station base into wood wall framing using (2) Phillips head screws. Pilot drill mounting holes using a 3/32" bit. Use 2 of 3 holes that best align with wood framing. CAUTION: Over tightening the screws could deform plastic base and interfere with circuit board snaps. NOTE: Insert bottom of circuit board behind bottom snap of wall station base. Pivot circuit board up until board snaps into place. For best results, press on circuit board between battery terminals. Insert battery onto circuit board being careful to match (+) positive battery marking with (+) circuit board marking. Align wall station cover/button assembly with base. Press cover assembly over base until cover snaps into place. A uniform seam between the cover and base indicates a proper installation. Step 10: Install Entrapment Warning Label Install Entrapment Warning Label next to wall station in a prominent location Install Entrapment Warning Label next to Wall Station as illustrated. If label adhesive will not adhere to the surface, secure the label by additional mechanical means such as staples, nails or screws. Step 9: Installing Deluxe Wireless Wall Station (if included) Install all wall controls out of the reach of children and in a location where the door can be seen before activating. Do not mount push buttons near or next to garage door. Locate a convenient place to mount wall station. To keep wall station out of the reach of children, measure at least five feet up from the floor and secure wall station base into wood wall framing using (2) Phillips head screws. Pilot drill mounting holes using a 3/32" bit. Use 2 of 3 holes that best align with wood framing. CAUTION: Over tightening the screws could deform plastic base and interfere with circuit board snaps. NOTE: Insert bottom of circuit board behind bottom snap of wall station base. Pivot circuit board up until board snaps into place. For best results, press on circuit board between battery terminals. Insert battery onto circuit board being careful to match (+) positive battery marking with (+) circuit board marking. Align wall station cover/button assembly with base. Press cover assembly over base until cover snaps into place. A uniform seam between the cover and base indicates a proper installation. Step 10: Install Entrapment Warning Label Install Entrapment Warning Label next to wall station in a prominent location Install Entrapment Warning Label next to Wall Station as illustrated. If label adhesive will not adhere to the surface, secure the label by additional mechanical means such as staples, nails or screws. Step 11: Install Wireless Infrared Safety Sensor Quick-Install (QI) Mounting Bracket. (If Opener is Equipped with Wired Infrared Safety Sensor Go to Step 15) Use the...

Herunterladen

Geben Sie zwei Ziffern: