Stimmen - 4, Durchschnittliche Bewertung: 4 ( )

Hersteller: Genie Dateigröße: 14.87 mb Dateiname: Unterrichtssprache:

Set the UP force level at the minimum force required to open door without stopping. 4. Once the desired level is selected, this stores the maximum force level for the UP direction in memory. ERASE - OPEN/CLOSE TRAVEL LIMIT 1. Press and hold both of the "SET" buttons ( SET & SET ) together until the green indicator light blinks (about 5 seconds). 2. All close and open travel limit settings are erased. Then follow the steps above to reprogram close and open travel limits. NOTE: The opener will not close the doorautomatically unless the Safe-T-Beam® System isinstalled. CONTACT REVERSE TEST The force adjustments and limit switch settings MUST BE COMPLETED before testing. 1. Testing. • Open garage door using Wall Button. – Place a 2" x 4" board (laid flat) under center of garage door opening (Fig. 6-6). • Close door using Wall Button. • When door contacts board, it must stop and reverse (within 2 seconds) to open position. 2. Adjustment. • If the door does not properly reverse. – Check to see if door has "close" limit programmed. It should not have reached its "close" limit before hitting board. – If the door STOPS but does not reverse, decrease "CLOSE FORCE" control CLOSE setting slightly (turn it counter-clockwise). • Test again. Repeat as necessary until door reverses upon contacting board. FIG. 6-6 2 x 4 under center of door opening. OPEN FORCE CLOSE Down Force Control Adjustment Up Force Control Adjustment ROTATE CLOCKWISE ROTATE COUNTER-CLOCKWISE FIG. 6-5 Force Control Adjustment. PN# 36420Supplement, 10/27/2008 PROGRAMMING REMOTE CONTROLS7 A moving door can cause serious injury or death. 1. Keep people clear of opening while door is moving. 2. Do NOT allow children to play with opener, including Wall Button, remote control, or Wireless Keypad. 3. During programming, the door opener could begin to run, so keep people and objects away from the moving door and its parts. To keep the door from moving, close the door and disconnect it from the Opener by pulling the Emergency Release. WARNING PROGRAMMING REMOTE CONTROLS7 A moving door can cause serious injury or death. 1. Keep people clear of opening while door is moving. 2. Do NOT allow children to play with opener, including Wall Button, remote control, or Wireless Keypad. 3. During programming, the door opener could begin to run, so keep people and objects away from the moving door and its parts. To keep the door from moving, close the door and disconnect it from the Opener by pulling the Emergency Release. WARNING NOTE: For remote control locate Box 3. 1a. Single Button Remote Programming. NOTE: This opener can learn up to 7 transmitterbuttons. • Locate learn code button and indicator LED on the power head (next to force adjustment screws) (Fig. 7-1). • Press and release learn code button. – Indicator LED will blink RED at a rate of twice per second. • Within 30 seconds, push remote control button once. – Indicator LED will stop blinking and stay on. • Press remote control button again. – Red LED will go out. Remote is now programmed. 1b. Multi Button Remote Programming. NOTE: Each button on a multi-button remote is designed for use with 1 door. You cannot program 2 buttons to operate the same door, norcan you program 1 button to operate 2 doors. You can program a maximum of 7 different transmitters or wireless devices. NOTE: Pushing two buttons simultaneously willerase programmed memory and limits must be reset. • For each button. – Program each button separately using the Single Button Remote Programming steps. 2. Operating. • Press remote button once. – Door will move. • Press button again. – Door will stop. • Press button again. – Door will move in opposite direction. NOTE: The door will stop automatically at thefully open or fully closed position. LOST OR STOLEN REMOTE 1. Clear memory. • Press and hold learn code button (on power head) for 10 seconds or until the red blinking indicator LED goes out. • Program remaining or new remote controls as done previously. Your door opener will no longer recognize any signal received from themissing remote control, or any other which hasnot been reprogrammed. FCC and IC CERTIFIED FIG. 7-1 Learn code button and LED SET SET OPEN FORCE CLOSE CODE LEARN LIMITMANUAL Open Travel Limit Open Set Limit Button Close Travel Limit Close Set Limit Button Down Force Control Adjustment Up Force Control Adjustment Learn Code Button LED Indicator Light To Garage Door This device complies with FCC Part 15 and RSS 210 of Industry Canada. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will no...

Herunterladen

Geben Sie zwei Ziffern: