Stimmen - 4, Durchschnittliche Bewertung: 4.3
(
)
)
|
Anleitung Zusammenfassung
Repeat for other section(s) except top section. IMPORTANT: PUSH & HOLD THE HINGE LEAFS AGAINST SECTION WHILE SECURING WITH (2) 1/4” -14 x 5/8” SELF TAPPING SCREWS. END AND INTERMEDIATE HINGES HAVE (2) SCREWS. NOTE: Install lock at this time (sold separately) see Side Lock installation instructions on page 25. 8 Power Drill 7/16” Socket Driver 9 Top Bracket Slide To install the top bracket slide, align the slots in the top bracket slide with the set of holes under the top sections u-bar. Loosely fasten the top bracket slide using (2) 1/4” - 20 x 1” carriage bolts and (2) 1/4” - 20 Nylock nuts to the u-bar. The top bracket slide will be adjusted and tightened in Step 13. Insert rollers into top bracket slide. Repeat for other side. TOP BRACKET SLIDE (2) 1/4” - 20 x 1” carriage bolts None HOLES TOP SECTION U-BAR (2) 1/4”-20 NYLOCK HEX NUTS ROLLER END HINGES INTERMEDIATE HINGES LOCK SECTION UPPERMOST HOLE (2)1/4” - 14 X 5/8” SELF TAPPING SCREWS 1/4” - 14 X 5/8” SELF TAPPING SCREWS UPPERMOST HOLE HINGE LEAF HINGE LEAF Tools Needed: 13 Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your local yellow pages/business listings or go to the Find a Dealer section online at Top Section Place the top section in the opening and vertically align with lower sections. Temporarily secure the top section by driving a nail in the header near the center of the door and bending it over the top section. Now flip up hinge leaf against section, fastening center hinges first, and end hinges last. (Refer to Step 8). When installing a door with Torquemaster® Plus counterbalance system, vertical track alignment is critical. Position flagangle between 1-11/16” (43 mm) to 1-3/4” (44 mm) from the edge of the door. Tighten the bottom lag screw. Flagangles must be parallel to the door sections. Repeat for opposite side. IMPORTANT: THE DIMENSION BETWEEN THE FLAGANGLES MUST BE DOOR WIDTH PLUS 3-3/8” (86 MM) TO 3-1/2” (89 MM) FOR SMOOTH, SAFE DOOR OPERATION. Now complete the vertical track installation by securing the center jamb bracket (s), flagangle, and connection of the vertical track/ flagangle. Repeat for opposite side. 10 Hammer Nail Tape Measure Step Ladder 1-11/16” TO 1-3/4” TOP FLAGANGLE SECTION NAIL TOP SECTION Door width + 3-3/8” - 3-1/2” NOTE: If you have fully adjustable flagangle, skip this step and complete Step 12. To install horizontal track, place the curved end over the top roller. Align key slot of the horizontal track with the quick install tab of the flagangle. Push curved portion of horizontal track down to lock in place. Level the horizontal track assembly and bolt the horizontal angle to the slot in the flagangle using (1) 3/8” - 16 x 3/4” truss head bolt and (1) 3/8” - 16 hex nut. Repeat for other side. NOTE: If an idrive® opener will be installed, position horizontal tracks slightly above level. Remove the nail that was temporarily holding the top section in place, installed in Step 10. DO NOT RAISE DOOR UNTIL HORIZONTAL TRACKS ARE SECURED AT REAR, AS OUTLINED IN STEP 24, OR DOOR COULD FALL FROM OVERHEAD POSITION CAUSING SEVERE OR FATAL INJURY. IMPORTANT: FAILURE TO REMOVE NAIL BEFORE ATTEMPTING TO RAISE DOOR COULD CAUSE PERMANENT DAMAGE TO TOP SECTION. NOTE: After completing this step, continue with step 13. KEY SLOT QUICK INSTALL TAB HORIZONTAL TRACK VERTICAL TRACK FLAGANGLE 9/16” Socket Ratchet Wrench 9/16” Wrench Level Step Ladder Attaching Horizontal Track to Quick Install Flagangle WARNING (1) 3/8”- 16 X 3/4” TRUSS HEAD BOLT (1) 3/8”- 16 HEX NUT HORIZONTAL TRACK HORIZONTAL ANGLE KEY SLOT QUICK INSTALL TAB HORIZONTAL TRACK VERTICAL TRACK FLAGANGLE Attaching Horizontal Track to Fully Adjustable Flagangle NOTE: If quick install flagangles were installed in Step 11, skip this step and continue with Step 13. To install horizontal track, place the curved end over the top roller. Align the bottom of the horizontal track with the vertical track. Hand tighten the horizontal track to the flagangle with a stud plate and (2) 1/4”-20 flange hex nuts. Level the horizontal track assembly and bolt the horizontal angle to the slot in the flagangle using (1) 3/8” - 16 x 3/4” truss head bolt and (1) 3/8” - 16 hex nut. Repeat for other side. NOTE: If an idrive® opener will be installed, position horizontal tracks slightly above level. Remove the nail that was temporarily holding the top section in place, installed in Step 10. DO NOT RAISE DOOR UNTIL HORIZONTAL TRACKS ARE SE CURED AT REAR, AS OUTLINED IN STEP 24, OR DOOR COULD FALL FROM OVERHEAD POSI TION CAUSING SEVERE OR FATAL INJURY. IMPORTANT: FAILURE TO REMOVE NAIL BEFORE ATTEMPTING TO RAISE DOOR COULD CAUSE PERMANENT DAMAGE TO TOP SECTION. WARNING 1/4”-20 FLANGE HEX NUTS FLAGANGLE (1) 3/8”- 16 X 3/4” TRUSS HEAD BOLT (1) 3/8”- 16 HEX NUT HORIZONTAL TRACK HORIZONTAL ANGLE Stud plate Tools Needed: Tools Needed: 14 Please Do Not Return This Product To The Store. Contact...