Stimmen - 2, Durchschnittliche Bewertung: 5
(
)
)
|
Anleitung Zusammenfassung
Otherwise, check if the battery is inserted properly. -The left button on the transmitter should be pressed, not the right button -If the red light on the receiver flashes when you press the left button on the transmitter, but the door opener does not respond, please ensure the red/black wire is successfully connected from the receiver to the wall mounted door control. -Ensure the wires that are previously connected to the wall mounted door control are not loose. -Ensure the code setting on the transmitter is the same as the receiver. Refer to section 4 to check the code setting. 4. CHANGE THE OPERATION CODE FOR BOTH TRANSMITTER AND RECEIVER It is recommended to randomly set the operation code for your remote control to avoid interference from other devices. Follow the instructions below to change the operation code. 1 Pry off the battery cover of the transmitter with a coin, as shown. You will see 9 connectors labeled from “1” to “9”, as shown. (the connectors setting may not be the same as shown.) BATTERY You can randomly remove some connectors, leaving some 2 in place. A connector can be removed with the clip, as shown. 4. CHANGE THE OPERATION CODE FOR BOTH TRANSMITTER AND RECEIVER (CONT) 4. CHANGE THE OPERATION CODE FOR BOTH TRANSMITTER AND RECEIVER (CONT) 5. BATTERY 3 4 If the connector is placed on the top and middle posts, that column is set on “ + ” . If the connector is placed on the middle and bottom posts, that column is set on “ - ”. If the connector is removed completely, (not placed on any posts), it is set to “ 0 ”. (see diagram for examples of how to set a column to the three different positions). When removing a con ‘+’ nector to set a column to “ 0 ”, save the connector in case you change the code at a later date. ‘-’ ‘0’ After setting up the code connectors on the transmitter, you are ready to set the same code on the receiver. WARNING Remove the receiver from the electrical outlet before changing the code. 5 Remove the screw that holds the connector cover, and remove the cover. 6 You will see 10 connectors. For connec tors “1” to “9”, the settings must match with those of the transmitter. Connectors 1 to 9 are the same. BATTERY 7 For connector “10” on the receiver, set the connector on “+” if you are using button “1” to control this receiver. If you are planning to use button “2” to control this receiver, you need to remove this connector. See diagram below. RECEIVER RECEIVER Connector 10 “Removed” TRANSMITTER Button 2- Right button Connector 10 set to “+” TRANSMITTER Button 1- Left Button 9108 Put the cover and screw back onto the receiver. Plug the receiver into an electrical outlet. Put the battery cover back onto the transmitter. Press the designated button on the transmitter to operate the garage door. 12 volt alkaline battery (size 23A) (included). It is time to change the battery when the red LED on the transmitter does not turn on when either button is pressed. 6. ADDITIONAL RECEIVER There are 2 buttons on your transmitter, the other button can be used to control another Skylink® Garage Door Receiver Model 318R (sold separately) or Skylink® Wireless Switch Receiver Model SW-318R (sold separately). 7. ADDITIONAL TRANSMITTER You can add as many additional transmitters as you want to control the same receiver. Simply set the same operation code on all transmitters with the same code setting on the receiver. Skylink® offers Keychain Transmitter Model 318TN and Keyless Entry Transmitter Model 318K to work with your receiver. For more information, please visit our website at or contact us. 8. CAUTION RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY. CAUTION : DISCONNECT POWER BEFORE CODE CHANGING. REPLACE COVER AFTER CODE CHANGING. Maximum Rating: Input : 120VAC 60Hz 2W 9. FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of th...