Stimmen - 0, Durchschnittliche Bewertung: 0
(
)
)
|
Dieses Gerät hat auch andere Anweisungen:
Anleitung Zusammenfassung
E
E
N
N
Installation Guide (Continued)
G
G
L
L
I
I
S
S
H
Speakers
❐ Final Checks
❐ Installation Procedures
H
Connect the speaker wires. See the wiring diagram
35
1. Make sure that all wires are properly connected
First complete the electrical connections, and
Insert mounting collar 1 into the dashboard, and
36
(➡ page 60) for the proper hookups. Follow the di-
and insulated.
then check them for correctness. (➡ page 60)
1 bend the mounting tabs out with a screwdriver.
agram carefully to avoid damaging the speakers
2. Make sure that the stereo unit is securely held in
The included mounting collar 1 is designed
and the stereo unit.
Fastening the mounting collar
the mounting collar.
specifically for this unit. Do not use it to attach
The speakers used must be able to handle more
The tabs to be bent vary depending on
3. Turn on the ignition to check the unit for proper
any other model.
than 50 W of audio power. If using an optional
the car. Bend them with a screwdriver
operation.
audio amplifier, the speakers should be able to han-
; Flat-head screw
to fasten the mounting collar 1 se-
dle the maximum amplifier output power. Speakers
If you have difficulties, consult your nearest author-
(5 mm·a6 mm)
curely in the dashboard.
with low input ratings can be damaged. Speaker
ized professional installer for assistance.
Dashboard
impedance should measure 4–8 ≠, which is typi-
: Mounting
cally marked on most speakers. Lower or higher
❐ Preparation
spring (L)
Tab
impedance speakers will affect output and can
cause both speaker and stereo unit damage.
≥ We strongly recommend that you wear gloves
6 Power
1 Mounting collar
Motor Antenna
for installation work to protect yourself from
connector
Connect the car motor antenna lead to the dark blue
injuries.
Tab
motor antenna relay control lead.
≥ When bending the mounting tabs of the
(Do not confuse the antenna lead with blue/white
mounting collar with a screwdriver, be careful
Note:
stripe lead for a power amplifier.)
not to injure your hands and fingers.
≥ To securely install the unit, fully bend a
Mounting tab
Battery
number of the tabs so that there is no
Connect the yellow battery lead to the correct radio
5 Mounting bolt (5 mm·)
rattling.
≥ Disconnect the cable from the negative - battery
wire or to the battery fuse port on the fuse block.
terminal (see caution below).
9 Mounting spring (R)
≥ Be sure to fasten the unit securely when
joining it with the mounting collar 1.
Antenna
≥ Unit should be installed in a horizontal position
; Flat-head screw (5 mm·a6 mm)
Connect the antenna by plugging the antenna lead
with the front end up at a convenient angle, but
into the antenna receptacle.
Attach the mounting springs 9, : to the unit.
not more than 30o.
2
Equipment
Connect any optional equipment such as an amplifi-
Secure the rear of the unit.
er, according to the instructions furnished with the
3 After fixing mounting bolt 5 and power connector
equipment. Leave about 12z (30 cm) of distance
6, fix the rear of the unit to the car body by either
between the speaker leads/amplifier unit and the
Less than 30x
method (a) or (b) shown below.
antenna/antenna extension cord. Read the operat-
Insert trim plate 8.
ing and installation instructions of any equipment
4
you will connect to this unit.
Caution:
Note for the trim plate 8:
After installation, recon-
Power
≥ Do not disconnect the battery terminals of a
≥ Attach the trim plate after attaching the
5 nect the negative
Connect the red power lead to the correct car radio
- bat-
car with a trip or navigational computer since
main unit to the vehicle. Remove the
tery terminal.
wire or to the appropriate fuse port on the fuse
all user settings stored in memory will be lost.
front panel to attach the trim plate.
block.
Instead take extra care with installing the unit
If the stereo unit functions properly with all these
to prevent shorts.
(a) Using the rear support strap 3
(b) Using the rubber cushion (option)
connections made, disconnect the wires and pro-
ceed to the final installation.
Fire wall of car
Dashboard Installation
4 Tapping screw
Rear support bracket
❐ Final Installation
Installation Opening
Rubber cushion (option)
(5 mm
(provided on the car)
·a16 mm)
3 mm·
Lead Connections
23/32q
2 Hex. nut
Connect all wires, making sure that each connec-
(53 mm)
(5 mm
tion is insulated and secure. Bundle all loose wires
·)
75/32q
and fasten them with tape so they will not fall down
(182 mm)
3 Rear support
later. Now insert the stereo unit into the mounting
strap
5 Mounting bolt
collar.
This unit can be installed in any dashboard having
(5 mm·)
an opening as shown above. The dashboard should
5 Mounting bolt
Congratulations! After making a few final checks,
be 3⁄
(5 mm·)
1 Mounting collar
16z (4.75 mm)j7⁄32z (5.56 mm) thick in order to
you’re ready to enjoy your new auto stereo system.
be able to support the unit.
1 Mounting collar
56
57
CQ-DF802U
CQ-DF802U
...