Stimmen - 2, Durchschnittliche Bewertung: 4
(
)
)
|
Anleitung Zusammenfassung
CAUTION! Make sure your radio isn’t in a place where it could interfere with driver visibility or safe deployment of the airbags. Option 2 jump sel Dash Mount Installing the Dash Mount: CAUTION: The adhesive used on the Dash Mount may be difficult to remove. Do not install this mount on leather surfaces (contact your vehicle dealer if you are unsure about your dash surface), and make sure the air temperature is at least 60uF (15uC) during installation. If it’s not at least 60uF, turn on the heater in your vehicle to bring the temperature up to 60uF. 1 Locate a flat surface for the Dash Mount. (Options 1, 2, or 3.) Make sure there is ample room for the dock and radio when installed. 2 Set the orientation of the mount before adhering it. Loosen the knob and adjust the adhesive foot for the location you selected: • Option 1 & Option 3 should be oriented as I. • Option 2 should be oriented as II. 3 Clean the surface with the alcohol preparation pad, and let it dry thoroughly. 4 Attach the Dash Mount to the PowerConnect Vehicle Dock using the provided screws. 5 Peel off the adhesive liner. Position, press, and hold the Dash Mount in place for 30 seconds. IMPORTANT! Allow the Dash Mount adhesive to cure (dry) for a minimum of 2-4 hours before using the mount. The best adhesion occurs after 24 hours. 6 The dock mounting plate can be tilted in different directions. Adjust as necessary for your particular vehicle. When the orientation is correct, tighten the knob. Option 3 jump sel Option 1 sel jump I II Knob Adhesive Foot Dock Mounting Plate Option 5 jump sel Option 4 jump sel Vent Mount Installing the Vent Mount: 1 Locate a suitable vent in your vehicle which is strong enough to hold the Stratus 6 and the PowerConnect Vehicle Dock. (Options 4 or 5.) 2 If the vent louvers are recessed, you’ll have to use the extended vent clamps. The Vent Mount is assembled with the short vent clamps, so you will have to remove the short clamps and install the extended clamps as shown below. 3 Attach the Vent Mount to the PowerConnect Vehicle Dock using the provided screws. 4 Push the Vent Mount onto the vehicle vent as shown (1) until hooked on the rear of the vent louver (2). 5 Rest the foot against the bottom of the vent (2). If necessary, adjust the tilt of the Vent Mount by repositioning the foot to a different tilt adjustment hole (3). Extended Vent Clamps Short Vent Clamps Remove End Cap Slide Short Vent Clamps Out Slide Extended Vent Clamps In Replace End Cap PUSH Dash Vent Louver Vent Vent Dash Dash HOOKED TILT ADJUSTMENT HOLES FOOT 1 2 3 AUDIO ANT AUDIO ANT AUDIO ANT Mount the Magnetic Mount Antenna Choose the best location for the antenna considering your vehicle type. Refer to the antenna placement tips and cautions in the User Guide beginning on page 23. • Sedan or Coupe: We recommend mounting the antenna above either the front windshield or the back window. • Pickup Truck: We recommend mounting the antenna above the front windshield. • Convertible: We recommend mounting the antenna at the leading edge of the trunk. • SUV: We recommend mounting the antenna at the rear of the roof. CAUTION! STOP and read the more specific instructions in the User Guide for all types of vehicles — or get someone who knows vehicles to help — if you don’t understand what to do. You might accidentally do damage to your vehicle. Attach the Rubber Tail to the antenna and press the antenna cable into the Rubber Tail. Use the Rubber Tail to position the antenna the correct distance from the edge of the roof or trunk lid. Clean the surface of the selected mounting location using the alcohol preparation pad and let it dry thoroughly. Peel the protective material from the adhesive strips and press the Rubber Tail firmly into place on the vehicle for 30 seconds. At room temperature (68° F), maximum adhesion usually occurs within 72 hours. During this period, avoid car washes and other contact with the antenna and the Rubber Tail. Feed the antenna wire under the rubber molding around the front or rear windshield, and into the seal around the trunk or door. For a convertible, the cable can be routed directly into the trunk. TIP! Use a tool like a blunt plastic putty knife, a credit card, a plastic knife, or a similar blunt tool to help hide wires along the windshield trim. Hide the Magnetic Mount Antenna Cable Inside the Vehicle The best place to hide your antenna cable depends on your type of vehicle. When the antenna is mounted at the rear of the vehicle, it’s usually easiest to run the cable from the rear to the front toward the radio by routing the cable along the interior trim where it meets the carpet, gently pushing it behind the edges of the trim. Bring the cable out from the trim and route it under the carpet toward the dashboard. When the antenna is mounted at the front of the vehicle, bring the cable into the rubber weather stripping around the door to the bottom of the door opening. Bring the cable out of the weather stripping and route i...
Dieses Handbuch ist für folgende Modelle:Car-Receiver - Stratus 6 SDSV6QSG 092109a (2.38 mb)